Go Back   Forno Bravo Forum: The Wood-Fired Oven Community > Regional Forums > Australia

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 09-13-2012, 05:43 AM
Serf
 
Join Date: Jul 2012
Location: Brisbane, Australia
Posts: 21
Default Harro's parrilla (bbq and box oven) build in Brisbane, Aust

G'day all,

I've finally started on my Argentinean style parrilla bbq and oven. My take on this simple but effective wood fired grill is to have a firebox area in the lower left, that heats up a little oven box created out of firebrick slabs straight above it (upper left). Hopefully it will heat this little box up enough to do bread, spuds, empanadas etc, and maybe even pizza if i'm lucky. But the main idea is for the fire to create white hot coals that are spread under a moveable grill which takes up the whole right hand side, to slow cook meats of all kinds. There is a short dividing wall between the two to keep ash etc away from the food on the grill.

I've had the pros in to lay the blocks properly (given it is 3.6m tall and will be supporting both a patio and shed roof eventually), and now i'm doing the rest myself. I poured the concrete slab benches, and have installed the galvanised hood inside the blockwork, which will have an 1800mm long, 200mm diameter flue attached which will poke through the tin roof that will go on top (cowl height will be a whopping 4.5m off ground to get good draw and hopefully no complaints from any neighbours about smoke!?).
Attached Thumbnails
Harro's parrilla (bbq and box oven) build in Brisbane, Aust-img_0613.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-image001.jpeg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-image004.jpeg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-image005.jpeg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-img_0668.jpg  

Reply With Quote
  #2  
Old 09-13-2012, 05:59 AM
Serf
 
Join Date: Jul 2012
Location: Brisbane, Australia
Posts: 21
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

Now i'm about to start lining the base and walls of the oven/bbq with 25mm ceramic board insulation on the base, topped by firebricks, and 25mm firebrick splits directly on the corefilled block walls.

I'm wondering how should i fix the firebricks/splits to the inside wall, and whether anything is needed on the base (apart from just gravity)? And also the short internal dividing wall between the firebox and the grill, which will be built up with standard size firebricks. I know fireclay mortar mix would be best, or Ryland? I'm going to pick up all the firebricks from Claypave within days so only want to make one trip. The 25mm splits that will line the walls probably need a nice sticky mix. The internal dividing wall isn't as crucial for heat retention as say a dome oven as heat is ok on both sides of the wall. So I was contemplating standard premixed mortar in a bag.

For interest i'll post a couple of pics of my wife's relatives' parrillas in Argentina, along with one of my plan.
Attached Thumbnails
Harro's parrilla (bbq and box oven) build in Brisbane, Aust-la-foto.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-p1020330.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-p1020333.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-p1020321.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-oven-box.jpg  

Reply With Quote
  #3  
Old 09-13-2012, 06:43 AM
Laborer
 
Join Date: May 2011
Location: Brisbane Australia
Posts: 62
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

"25mm ceramic board insulation on the base, topped by firebricks, and 25mm firebrick splits directly on the corefilled block walls."

I think I get the idea of your build. Usually the insulation on a base is thicker than 25mm. I used 50mm of calsil. I am not sure how it will go putting firebrick split on the core filled blocks because the heat will transmit through the firebrick to the blockwalls - you will loose heat, 25mm splits will not hold much and not sure how the heat may damage your blockwork through expansion. The base insulation holds the heat in the oven and insulates the floor from any heat damage. On a pompeii oven the dome is insulated to hold in the heat. I would be thinking about insulating the walls and using firebrick thicker than 25mm so the walls free stand. No sure how you were going to hold up the box roof.

I would use poor man's mortar which has fireclay and lime (with sand and cement). You can buy the fireclay at claypave.

Brett
Reply With Quote
  #4  
Old 09-13-2012, 08:34 AM
deejayoh's Avatar
Il Pizzaiolo
 
Join Date: Jul 2010
Location: Seattle
Posts: 1,380
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

I have to admit I am a bit confused. I have seen more than a few parillas in my day.
Are these things usually insulated? It seems a bit of a waste when the front is wide open and the flue is right out the top. Is heat retention an issue, or will you have a live fire going for cooking all the time? Or are you just talking about insulating your oven box?
__________________

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #5  
Old 09-13-2012, 02:18 PM
Serf
 
Join Date: Jul 2012
Location: Brisbane, Australia
Posts: 21
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

Brett - what type of insulation would you suggest for the walls and how do you install that and the firebrick onto the vertical block wall? The top, bottom and back of the oven box are just 450wide x 300 x 50thk firebrick slabs that will span from the blockwork to the internal dividing wall.

deejayoh - fair enough questions, it is a bit of a strange one, particularly here in Australia. My parrilla design is a bit of a mix of others i've seen around Argentina, but using the knowledge of pizza oven builders from here, and based around easily available materials here in Brisbane.

A standard parrilla doesn't have any insulation, just fire bricks (sometimes not even that) and yes has a fire going the whole cook time to keep feeding fresh hot coals under the grill. The front grill is wide open, but often has a steel sheet door that you can remove to attend to the grill, and replace to help retain heat. The two parrillas I posted pics of above have hinged doors, one upwards and one to the side.

So insulating the grilling area may be a little bit of a waste, but maybe the firebox area and oven area should be...? I was planning to put 25mm ceramic board above the top of the oven box to help heat retention.
Reply With Quote
  #6  
Old 09-17-2012, 06:05 AM
Laborer
 
Join Date: May 2011
Location: Brisbane Australia
Posts: 62
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

Quote:
Originally Posted by harro View Post
Brett - what type of insulation would you suggest for the walls and how do you install that and the firebrick onto the vertical block wall? The top, bottom and back of the oven box are just 450wide x 300 x 50thk firebrick slabs that will span from the blockwork to the internal dividing wall.

So insulating the grilling area may be a little bit of a waste, but maybe the firebox area and oven area should be...? I was planning to put 25mm ceramic board above the top of the oven box to help heat retention.
Yes I was imaging insulating the oven section above firebox area only, but if you have a fire going underneath the oven most of the time then maybe insulation isn't much value - just use fire bricks to hold heat and the fire maintains desired temperature. All insulation is going to do is keep the heat in and reduce heat loss so the oven stays hot longer without a fire.

You could use ceramic insulation or calsil board (it is cheaper). If you decide to use insulation, you will have to make everything self supporting/standing so the insulation just sits in a gap/space created between the your blocks and firebricks. Hope that makes sense.

Brett
Reply With Quote
  #7  
Old 09-23-2012, 08:44 PM
Serf
 
Join Date: Jul 2012
Location: Brisbane, Australia
Posts: 21
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

Starting to feel like I知 getting somewhere which is nice!

Installed the hood, flue and cowl, and tin roof over the structure on the weekend. Bought a red silicon pipe flashing ($47) to go around the flue. Also had some mates in to help with the new insulated patio roof.

Made the trip out to Dinmore and bought over $500 worth of firebricks (phew), and did a mockup of how the internal wall and oven box will look (see pic). Next weekend I値l be installing it all.. The owner of Claypave recommended Rylbond to use for lining the walls with splits, and for mortaring the internal wall. But it only needs 2mm thickness between bricks so I値l have to be careful with that. Anyone on here used this stuff? I figured I don稚 need a huge amount (unlike a pizza dome) so a pre-mixed option should be quicker and easier than fireclay mortar mix.

Biggest challenge now is how to support the roof of the oven box. It was going to be like the base (450x300x50 slab) but I decided to use that as the RHS wall instead, and as I bought only 3 slabs I知 now going to put a couple of brackets spanning from side to side and put standard firebricks over the top, which will rest on the brackets and the edges of the back wall/side walls. Then a layer of insulation over the top.

Brett, I think I値l only be able to put insulation above the top of the oven box (apart from on the base of course). maybe I値l have a bit left over to sandwich inside the steel door to the oven that I値l need to get made up (anyone have any suggestions on who/where makes custom steel oven doors?).

Thanks again for any tips or advice to avoid blunders!
Attached Thumbnails
Harro's parrilla (bbq and box oven) build in Brisbane, Aust-photo-2a.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-photo-3a.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-photo-4a.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-photo-1a.jpg  
Reply With Quote
  #8  
Old 09-27-2012, 04:09 AM
Laborer
 
Join Date: Jul 2012
Location: Brisbane Australia
Posts: 60
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

Harro, that is one monster of a build. Will be very interested to see how it works - Legendary
Reply With Quote
  #9  
Old 10-12-2012, 05:35 AM
Serf
 
Join Date: Jul 2012
Location: Brisbane, Australia
Posts: 21
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

Thanks Camo. Here is the progress so far. All the base insulation, firebrick lining and internal wall and oven are in. I still need to tidy up the grout. The doors to the fire area and oven are next and have me a bit stumped as the surfaces to close on aren't exactly even all around. Hopefully some glass rope will act like a gasket to seal the oven shut. Unfortunately don't quite have enough CF board leftover to insulate both doors so might do one in Hebel as described in Dave's thread. Need to locate some materials this weekend and at least work out the plan for the doors, as i want to get stuck into the stone cladding on the outside of the block pretty soon, and get the grill in place.

cheers
harro
Attached Thumbnails
Harro's parrilla (bbq and box oven) build in Brisbane, Aust-img_0723.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-img_0725.jpg   Harro's parrilla (bbq and box oven) build in Brisbane, Aust-img_0740.jpg  
Reply With Quote
  #10  
Old 02-10-2013, 09:41 AM
Serf
 
Join Date: Feb 2013
Location: Australia
Posts: 1
Default Re: Harro's parrilla (bbq and box oven) build in Brisbane, Aust

Hi Harro,

I was wondering where you got you grill asembly from?

Thanks

Guillermo
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 03:19 AM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
ゥ 2006/10 Forno Bravo, LLC