#1  
Old 03-02-2009, 11:41 AM
Serf
 
Join Date: Jul 2008
Location: Fremont, ca
Posts: 12
Default Venting Vertical to Ctr of Dome

Team,

I need help. I'm novice at buiding the oven and need some/lots of help.

Iím building a 42Ē Pompeii (it's all done and looking good) and now designing the venting. My venting will start above the outside of the oven entrance and will traverse outside of the dome to the center of the dome and then up vertical.

This design will require two Dura Tech elbows; one at the arch and one on the center of the dome. The issue is cost. The Dura Tech 30 degree elbows run $200+ each, are there more cost effective elbows that I can purchase that will suffice the requirement for a flue design? Also, what about effective venting/draw in my design?

Thank you for any help/guidance you can provide me.

Cheers,

Domenico
Reply With Quote
  #2  
Old 03-02-2009, 12:24 PM
dmun's Avatar
Moderator
 
Join Date: Jul 2005
Location: New Jersey USA
Posts: 4,216
Default Re: Venting Vertical to Ctr of Dome

The engineered chimney systems are expensive, compared to flue tiles, but they are lightweight and can be secured to the structure without additional bracing for an offset flue like the one you're planning. It all comes down to a cost/time tradeoff like so many things in life. If your centered flue structure is some kind of structural masonry like brick, it will be fairly easy to add supports for the flue tile. If your superstructure is a lightweight metal stud with wonderboard construction, you should probably spring for the flue system.
__________________
My geodesic oven project:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
,
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #3  
Old 03-02-2009, 03:36 PM
Serf
 
Join Date: Jul 2008
Location: Fremont, ca
Posts: 12
Default Re: Venting Vertical to Ctr of Dome

Thank you for the reply.

I followed the FB plan exclusively. I have the arch built with recommended firebrick and structurally it is very sound.

Are you suggesting that I have the option in using a tile flue? I didnít know this was an option. I plan to enclose the dome with walls constructed with metal 2x4 studs all around so it is very possible to add additional studs in the interior as a way to offset the added weight of the flue and chimney components. Are tile flues and necessary elbows and stuff available?

Thank you,

Domenico
Reply With Quote
  #4  
Old 03-02-2009, 07:32 PM
dmun's Avatar
Moderator
 
Join Date: Jul 2005
Location: New Jersey USA
Posts: 4,216
Default Re: Venting Vertical to Ctr of Dome

Sure, flue tiles are available at any brickyard. The 8 x 8 size is what you need. They come in 24 inch lengths, and are attached to each other with a refractory cement like heat-stop. There are no elbows: if you need a bend, you cut an angle with a diamond blade in your angle grinder. I'm not going to pretend this is a fun process. The flue tiles are very heavy, you are probably going to need some kind of support beyond the flimsy interior metal studs. You can see what I did, on my linked project page (I think the flue is on part two) and I had only a small offset. I actually built a reinforced concrete bridge over my dome, but this was to support the two story masonry chimney I built.
__________________
My geodesic oven project:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
,
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #5  
Old 03-03-2009, 08:52 AM
Serf
 
Join Date: Jul 2008
Location: Fremont, ca
Posts: 12
Default Re: Venting Vertical to Ctr of Dome

Wow! You did a great job. No way I can accomplish thi. I think I'll go the expensive route.

What do I build on the top of my 6”x10” opening in the arch for venting? Do I build a rectangular box using firebrick so I can attach my anchor plate? How high should I build this and how do I attach the Dura Tech anchor plate (e.g. anchor bolts are each end and heatstop)?

As you can see I am very novice on this flue, flue liner and chimney stuff so please excuse my ignorance.

I’ve been reading many of the post on the forum and it’s helped me a lot but still have some things I need help with.

I appreciate your help.

Thanks,

Domenico
Reply With Quote
  #6  
Old 03-03-2009, 09:39 AM
dmun's Avatar
Moderator
 
Join Date: Jul 2005
Location: New Jersey USA
Posts: 4,216
Default Re: Venting Vertical to Ctr of Dome

I tried to find it for you, but the forum founder, James, did an offset flue with the stainless chimney system, in an enclosure like the one you plan. Maybe James will jump in and point to the construction photos of his oven (the one you see in his avatar)
__________________
My geodesic oven project:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
,
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #7  
Old 03-03-2009, 10:44 AM
Serf
 
Join Date: Jul 2008
Location: Fremont, ca
Posts: 12
Default Re: Venting Vertical to Ctr of Dome

Awesome! I'll wait for James to share some photos. it's raining here in the SF Bay Area (Fremont, Ca.) but if it stops I'm planning to build the exterior arch and vent this weekend, so hopefully I can get some ideas before this weekend. Just received Refmix from FB to complete the final arch and a bit of interior gap cementing. I've attached pic of what the oven entrance arch (reveal) looks like.

It would also be good to go into more details of the venting construction in the FB Pompeii Oven Plan. The FB plan was very, very good in the construction of the base, hearth and dome, including the arch, but lacked a bit of detail in the venting as it applies to the Dura Tech flue system.

I appreciate your help and technical guidance. I'm almost there and excited to better understand how to construct my venting. I hate to screw things up at this stage.

Thanks!
Venting Vertical to Ctr of Dome-ovenopening2.jpg
Reply With Quote
  #8  
Old 03-03-2009, 11:55 AM
wlively's Avatar
Journeyman
 
Join Date: May 2005
Location: Spring Branch, TX 78070
Posts: 384
Default Re: Venting Vertical to Ctr of Dome

You may want to consider going another route. You could use KS-4 (or similar) and cast your transition piece. That way you can make it any shape you want. You could use it to go from the vent opening all the way to the top of the dome to mount you chimney to. I do not know if it would save you any $, it would take at least 2 maybe 3 - 50 lb bags ( I paid $50 each + $10 in stainless needles) and be a bit more work.

It worked out well for me.
__________________
Wade Lively
Reply With Quote
  #9  
Old 03-03-2009, 07:31 PM
dmun's Avatar
Moderator
 
Join Date: Jul 2005
Location: New Jersey USA
Posts: 4,216
Default Re: Venting Vertical to Ctr of Dome

The reason that the venting instructions are vague is that builders use a multitude of building methods for the flue. It's true, though, that most ovens vent straight up from the mouth of the oven: This reduces the complexity by an order of magnitude. There are basically three elements: some kind of inverted funnel to channel the smoke into the flue, a length of stainless flue system or refractory flue tile, and some kind of enclosure to cover it up. Everything else is commentary.
__________________
My geodesic oven project:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
,
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #10  
Old 03-05-2009, 10:36 AM
Serf
 
Join Date: Jul 2008
Location: Fremont, ca
Posts: 12
Default Re: Venting Vertical to Ctr of Dome

I’m planning to use clay liners as a way to get the angel needed to vent outside and uo center of dome. I’ll have to build a superstructure to support the clay liners…no problems.

Critical concern: I calculated the angle needed to vent towards the center of the oven to be 65 degrees. Is this angle too steep, which will affect draw efficiency? Has anyone on the forum done this? I’m still waiting for James to reply as I understand he has done something similar.

Thank you,

Domenico
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Steel Dome Oven Wiley Other Oven Types 195 01-14-2014 11:06 PM
Igloo style dome insulation Throw Deep Pompeii Oven Construction 19 12-18-2009 02:40 PM
roof pitch and dome thickness ttriche Newbie Forum 0 11-08-2008 08:47 PM
Exterior Dome Construction Bandrasco Pompeii Oven Construction 19 10-26-2008 06:26 AM
A Potential New Low Dome Design james Pompeii Oven Construction 17 08-14-2008 12:44 PM


All times are GMT -7. The time now is 11:03 AM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
© 2006/10 Forno Bravo, LLC