#1  
Old 06-25-2008, 09:27 AM
Apprentice
 
Join Date: Jul 2005
Location: Toronto
Posts: 106
Default Mortar Choices

Hi I have a question for the community. The last oven I built I used a combination of pre-mixed refractory mortar for the inside joints and then filled the outer larger joints of the bricks with a mix of sand, clay and portland cement as described in Allan Scott's Bread Builders book. The reason for this is because the pre-mixed stuff did not reccomend large joints and it was more expensive than the home made brew. So far 2+ years later no visible issues or damage has occurred to it. But as usual I always try to improve on things and after all it is a big exepense to build one and last thing I would want to see is it fail and crumble before my eyes.

Are some of you just using Heastop 50 dry mix and filling the entire gap? As you roll the top of the dome those outer edges are pretty big gaps.

Thx.
Attached Thumbnails
Mortar Choices-img0336.jpg  
Reply With Quote
  #2  
Old 06-25-2008, 10:06 AM
Serf
 
Join Date: Sep 2007
Location: Milford, Michigan
Posts: 9
Default Re: Mortar Choices

I just completed my dome last weekend. Used Heatstop for the whole thing. The best thing I liked about it was the tacky quick-set properties. I didn't use any forms to build my dome. Once two bricks were set in a course they would support themselves in place...vertically. The downside is that I used 2.5 40lb bags at $60 a bag.

The rest of the story is that I started with one of the premix refractory cements, forget the name at the moment. Was to thin for my liking and I found it difficult to work with...have nearly a full bucket sitting in the garage and not sure what to do with it.

The other panic attack I had was that my local distributer only had two bags of Heatstop and I polished that off just as I was at the final 3 courses....yeah the toughest ones. So I bought the fireclay, mortar, and sand and tried that approach. I'm sure it works great but after building with no forms up until that point I didn't want to stop what I was doing and start working on forms, and my fireclay mixture was not going to support those last few courses without a form. So I called my distributer and he luckily had found another bag...so the day was saved.
Summary: of the three I tried; Heatstop, Pre-Mix, and homemade the Heatstop was by far the easiest to work with.
Reply With Quote
  #3  
Old 06-25-2008, 10:10 AM
Serf
 
Join Date: Sep 2007
Location: Milford, Michigan
Posts: 9
Default Re: Mortar Choices

I should also mention that I did use the "Homebrew" to do the cladding coat once the brick work was complete.
Reply With Quote
  #4  
Old 06-25-2008, 11:47 AM
Apprentice
 
Join Date: Jul 2005
Location: Toronto
Posts: 106
Default Re: Mortar Choices

When I did the last one I could not find fireclay specifically. I ended up buying Gold Art Clay which is used for making clay products and is fired in kilns to get it's strength. Got it from a local art supply store. When folks refer to fireclay is this the same thing or actually another product that is best suited for the home brew?

Thx
Reply With Quote
  #5  
Old 06-25-2008, 02:24 PM
RCLake's Avatar
Journeyman
 
Join Date: Jul 2007
Location: Corsicana,Texas
Posts: 433
Default Re: Mortar Choices

I used 4-50 lb bags of Heat Stop 50 to do my 42" dome. I needed to fix a crack from the arch area to the top (also redid my vent) and felt I should send some business to James so I bought a bag of refmix from him.

The refmix was by far much stronger but a bit harder to work with (keep the bricks wet!). It's to bad the shipping cost is so high or I would recommend everyone going that way. Getting a bag to do the tie in of the dome to the front opening is something I would suggest strongly.
__________________
RCLake

"It's time to go Vertical"

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #6  
Old 06-25-2008, 08:07 PM
Il Pizzaiolo
 
Join Date: Jan 2007
Location: Tampa, FL
Posts: 1,446
Default Re: Mortar Choices

I used the Heatstop 50, good stuff. No issues with the wide joints - then again, my largest joints were only 1/4" between courses (on the outer face of the bricks), minimal to no mortar on the inside or on the sides (cut to fit with only enough side to side gap for a thin "glue coat" or mortar). Really would have like to try the refmix....I was even willing to eat the high shipping, but FB was out of stock and it was backordered.....I had no patience and couldn't wait. RC is one of a few that have used both and all seem to agree it sets stronger and harder than Heatstop. I would say if you can afford it, go with the best (and don't worry about the gaps, unless you are really deviating from the basic plans and creating some huge gaps - which case I would rethink the project).

RT
Reply With Quote
  #7  
Old 06-26-2008, 05:20 AM
Apprentice
 
Join Date: Jul 2005
Location: Toronto
Posts: 106
Default Re: Mortar Choices

Seems I am having trouble getting HeatStop 50. A local masonary supply store carries Alsey Flue Set Mortar which he says is essentially the same thing. Comes in dry form 50 LB bag and costs $90.00.

Alsey Refractories Co.: Firebrick, Mortar, Castables, Stain and Private Brand Products

Does anyone have any experience with this?

Thx
Reply With Quote
  #8  
Old 06-26-2008, 02:52 PM
Il Pizzaiolo
 
Join Date: Jan 2007
Location: Tampa, FL
Posts: 1,446
Default Re: Mortar Choices

OUCH! They think highly of their refractory mortar in Toronto......I only paid $55 for HeatStop 50. You should send a message to CJ (CanuckJim), I'm sure he can help you in sourcing affordable materials in your area. He is one of the most knowledgeable and helpful forum members.

RT
Reply With Quote
  #9  
Old 06-26-2008, 07:01 PM
sarah h's Avatar
Master Builder
 
Join Date: Sep 2007
Location: Ottawa, ON, Canada
Posts: 567
Default Re: Mortar Choices

Tdibratt,

I'm in Ottawa and ran into the same problem last year - $90, almost double the U.S. prices everyone else is paying, and especially irritating when the two currencies are pretty much on par (give or take a few cents)!

I tried haggling with no success so I drove to Watertown. You might want to consider taking a drive to Buffalo.

Where the flue set mortar, I don't feel qualified to comment on its suitability but I wouldn't just take the saleman's word for it as many people on this forum have been wrongfully assured that lots of other products are a good substitute - most are not. RTflorida's right - ask Canuck Jim (send a private message to ensure he sees it).

Good luck!
Reply With Quote
  #10  
Old 06-26-2008, 07:19 PM
Apprentice
 
Join Date: Jul 2005
Location: Toronto
Posts: 106
Default Re: Mortar Choices

I actually sent Superior Clay an email on this and here is what I got back. Seems i may be able to get it special order and I am sure it will be pricey. Most other places just carry CPD premixed. Alphatherm sells Superwet 3000 but they tell me they do not think it is non-water soluable.

Tony,

I looked around at the history of our dealers in the Toronto area and I didn't see anyone who was likely to stock the Heat Stop 50. There were several folks who had the Heat Stop Wet Mix. Any of those dealers would be able to order it for you. Your best bet would probably be Mason's Masonry. They have yards in Mississauga and Richmond Hill. I would contact them (I'm sure you already have once) and see if they'll order it for you. It shouldn't be a problem. There aren't as many people who currently inventory the dry mix Heat Stop. That trend is changing and I think within the next several years it will be more commonplace.

Thank You,

Dave Kopp
Superior Clay Corp.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
High Heat Mortar Primer james Getting Started 80 01-27-2014 06:40 PM
Can I use insulating vermiculite concrete instead of mortar clading waynebergman Pompeii Oven Construction 4 12-30-2009 06:20 PM
Refractory Mortar Vs. Regular Mortar OvenBoy Design Styles, Chimneys and Finish 7 10-09-2008 02:56 PM
Mortar Problem Jerald P Modular Refractory Oven Installation 5 07-01-2007 02:32 PM
Fire Mortar vs. Refax Refractory Mortar southpaw Pompeii Oven Construction 4 04-07-2007 05:02 AM


All times are GMT -7. The time now is 12:50 AM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
2006/10 Forno Bravo, LLC