#1  
Old 08-04-2011, 09:47 AM
Serf
 
Join Date: Mar 2010
Location: Asheville, NC
Posts: 16
Default Gardella 42" oven

Hello all,
I've been lurking in the forums for two years or so while in the planning stages of my oven. I finally have the time and property of my own to actually build the oven. Right now I'm drawing the oven in CAD and I have a question about the landing. I tried going though as many posts as possible prior to posting and I apologize if this has been addressed/asked before.

The Pompeii plans call for an 8" vent landing and a 12" oven landing; so that's a total of 20" in front of the opening to the oven. For a 42" oven, its another 42" to the back of the oven. So that's 62" (over 5') to get too the back of the oven.

I'm considering modifying the plans to have a 12" vent landing and eliminate the oven landing. I like the look of the oven landing but I'm concerned it will be difficult to reach the back the oven.

I'm wondering if really should be concerned? Is the length of a typical peel handle long enough to retrieve a pizza from the back of the oven without scorching your hand?

Thanks in advance
Reply With Quote
  #2  
Old 08-23-2011, 12:32 PM
Serf
 
Join Date: Mar 2010
Location: Asheville, NC
Posts: 16
Default Re: Gardella 42" oven

Well I got most of the details hammered out and submitted for a permit today. Shouldn't take long to get the approval (also have tentative approval from my wife).

I've never been this excited to dig a big hole before.
Reply With Quote
  #3  
Old 08-23-2011, 12:41 PM
Aegis's Avatar
Journeyman
 
Join Date: Jan 2008
Location: Southbury Ct. USA
Posts: 431
Default Re: Gardella 42" oven

Welcome to the best project you ever did! My vent is 8" deep and takes up that much of my landing! I don't recall total landing, but 15" comes to mind.
The vent area does not add to the landing, it takes some of the space above it. Hope that is clear and correct!
Enjoy the ride! John
__________________
Build Thread:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Photos:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Oven Blog:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #4  
Old 08-23-2011, 07:41 PM
Serf
 
Join Date: Aug 2011
Location: PERTH AUSTRALIA
Posts: 17
Default Re: Gardella 42" oven

Australia Perth

I've just started on latest project 42 inch wfo . I sure ive seen the angle for the soldier row on the forum but now cant find it !!!! Sio please can someone put me out of my misery and remind me of the angle to cut to the soldier bricks

Trev

Last edited by barhen; 08-25-2011 at 07:21 PM.
Reply With Quote
  #5  
Old 08-28-2011, 07:58 PM
Serf
 
Join Date: Mar 2010
Location: Asheville, NC
Posts: 16
Default Re: Gardella 42" oven

Official ground breaking this weekend! I only made one major mistake; I didn't have any beer to help with the digging I hope the construction goes relatively quickly. I hope to at least have the stand and prep table constructed before the freezing weather shuts me down. My wife thinks my son (now 3 mo. old) will be helping me finish the stone work on the outside I think she knows me too well.

@ John, thanks for the info. I ended up making the vent/landing area as wide as possible. Both in an effort to keep it from feeling too cave like/enclosed and giving me an area to stage the pizza before they go in the oven.

~Colin
Attached Thumbnails
Gardella 42" oven-ground-breaking-1.jpg  
Reply With Quote
  #6  
Old 10-04-2011, 10:56 AM
Serf
 
Join Date: Mar 2010
Location: Asheville, NC
Posts: 16
Default Re: Gardella 42" oven

Well, progress is about as fast as expected (which is to say slow). I finally got all the foundation trenches dug. I had to dig down 2' in order to get the top of the footings below the frost line. The stiff clay and rocks certainly didn't make that easy.

Now I need to set the concrete forms and start pouring concrete. Fall has arrived in NC and cold weather is around the corner. I better pick up the pace!
Reply With Quote
  #7  
Old 10-31-2011, 12:11 PM
Serf
 
Join Date: Mar 2010
Location: Asheville, NC
Posts: 16
Default Re: Gardella 42" oven

Finally made some solid progress on the base. I had some days to take off work (use it or lose it) and I put the time into the oven. Very satisfying work. Anyway, I posted a few pictures of my progress.

There ended up being a gas line going right through the middle of my oven location. So I had to do some creative engineering to get the walls to work out.

Still hoping to get the slabs poured before winter!
Attached Thumbnails
Gardella 42" oven-foundation.jpg   Gardella 42" oven-footing-2-poured.jpg   Gardella 42" oven-first-wall.jpg   Gardella 42" oven-walls-complete.jpg  
Reply With Quote
  #8  
Old 03-16-2012, 07:54 AM
Serf
 
Join Date: Mar 2010
Location: Asheville, NC
Posts: 16
Default Re: Gardella 42" oven

The weather is finally cooperating and I got my slab poured last weekend. I still need to double check but I think water is pooling is the middle of the slab. I'm wondering if I should level the slab with a cement/sand slurry or just pour my insulating concrete and leave it alone.

There was <1/4" of water is the center of the slab and I haven't had a chance to check for drainage.
Reply With Quote
  #9  
Old 03-16-2012, 01:11 PM
Mike D's Avatar
Journeyman
 
Join Date: Oct 2010
Location: Berkeley, Ca.
Posts: 342
Default Re: Gardella 42" oven

-Depending on how you are going to finish the oven (igloo or covered roof) the insulating concrete should work to give you a level surface to build the oven.
-Is the insulating concrete going to go all the way to the edges? Or more of an island?

Bring on the Pictures-

Mike
Reply With Quote
  #10  
Old 03-16-2012, 01:53 PM
Serf
 
Join Date: Mar 2010
Location: Asheville, NC
Posts: 16
Default Re: Gardella 42" oven

I'm not worried about the leveling the hearth, as you said the insulating concrete will take care of that.

I'm worried that if any water gets in, it could pool under the insulation. I've read a lot of (good) advice on this site recommending to slope the slab away from the center; but didn't keep that in mind building the forms. And I'm don't remember if it was in reference to igloo style enclosures.

I'm building a "house style" enclosure and the insulation will be set back from the edge of the concrete. The outside will be stacked stone so there wont be much opportunity for water to get in....but water is very determined. Thanks for the help!
Attached Thumbnails
Gardella 42" oven-slab.jpg  
Attached Files
File Type: pdf cross section.pdf (29.4 KB, 143 views)
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Why Italian Wood-Fired Ovens are Round james Newbie Forum 50 04-01-2014 09:14 PM
FINALLY!!! - Start Of Building My Oven Oven_Man Pompeii Oven Construction 249 03-14-2013 05:33 AM
Can you identify this oven? Argentina? Is it a good newbie oven? jdbizkits Newbie Forum 5 12-17-2009 06:37 PM
Oh no - my oven is wet PizzaArthur Firing Your Oven 36 11-23-2009 09:16 PM
Neapolitana Style Oven (31.5") southpaw Pompeii Oven Construction 4 08-11-2007 06:29 AM


All times are GMT -7. The time now is 06:14 PM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
2006/10 Forno Bravo, LLC