#1  
Old 02-20-2007, 05:04 PM
Serf
 
Join Date: Dec 2006
Location: Mill Valley, Ca 94941
Posts: 8
Default chimney-fluliner installation?

I'm planing on building a chimney, with blocks on 3 sides and bricks on the front. I want to use a Clay Fluliner, but I have no idea on how to install it. Is the Fluliner masoned in with the bricks and blocks? or does it have to be freestanding with an air gap? In this case how would it be supported? and can it be closed in on the top with mortar? The Fluliner will be sitting on top of an double-arch, which has a 6"X10" opening, and I plan on using a 8"X13" Clay Fluliner.

Is there anybody out there who can give me instructions installing this type of Chimney and Fluliner? Or are there any better ideas out there?

Thanks in advance for any help,

Rudi
Reply With Quote
  #2  
Old 02-20-2007, 07:31 PM
dmun's Avatar
Moderator
 
Join Date: Jul 2005
Location: New Jersey USA
Posts: 4,216
Default Re: chimney-fluliner installation?

The flue tile sits on top of your entry, and is refractory mortared to the brick arch. It should be carefully leveled, because the stuff is heavy and it has to be self supporting. The masonry enclosure is built around the flue tile, and has a half inch gap between the tile and the masonry. One "withe" or four inches of brick or block is called for by code. If you are building a tall chimney, you want your masonry enclosure to be independently supported, in other words, built up from the slab on two sides, rather than sit on the fire brick arch. At the top of the chimney, the flue tile stack is stabilized by a stone or cast concrete chimney cap. If cast, it should use a piece of flashing to allow slip between the cap and the flue liner: they heat and expand at quite different rates. This is less of a concern if your chimney is only four feet high or so, as is typical of outdoor ovens.

Only in high earthquake danger areas should there be anything between the flue liner and the masonry enclosure: in those cases a loose material like vermiculite is used to stablize the flue liner in the enclosure.

This is high building code stuff: most builders don't get this elaborate in free-standing ovens.
Reply With Quote
  #3  
Old 02-20-2007, 10:11 PM
Serf
 
Join Date: Dec 2006
Location: Mill Valley, Ca 94941
Posts: 8
Default Re: chimney-fluliner installation?

Thanks for the quick reply dmun.

The chimney will be 3'-4' tall .It will be sitting on a metal frame next to the arch, it is supported by blocks sitting on the hearth vermiculite insulation. Putting loose vermiculite between flu and liner is a good idea, since Sebastopol is in a earthquake zone. I'm planning on building my own cap out of bricks. If I understand you right,I have to put a flashing (spacer) between flu and chimney to stabilize the liner and assume it has to be vented because of the high temp between liner and flu.
Sounds like a job just for the looks.
I wonder if the same can be established just using a plain steel stovepipe. Hate to spend $ 260.00 for a stainless double wall pipe.

I appreciate any further help and suggestions

thank you,
Rudi
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Chimney options Yahoo-Archive Design Styles, Chimneys and Finish 3 10-01-2010 10:18 AM
Chimney / Flue Question.. johnrbek Pompeii Oven Construction 1 02-20-2007 03:07 PM
OOPS! I didn't use a clay liner in my chimney bruce324 Design Styles, Chimneys and Finish 6 01-21-2007 08:45 AM
Flue Chimney Tips Alf Design Styles, Chimneys and Finish 1 08-02-2005 07:07 AM
Construction of Chimney question dmun Design Styles, Chimneys and Finish 0 07-18-2005 08:08 AM


All times are GMT -7. The time now is 04:39 AM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
2006/10 Forno Bravo, LLC