Go Back   Forno Bravo Forum: The Wood-Fired Oven Community > Pizza Oven Design and Installation > Getting Started

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 06-01-2010, 07:35 AM
Peasant
 
Join Date: May 2010
Location: High Wycombe, UK
Posts: 34
Default Vermiculite vs perlite for insulation under the oven floor

Hey guys

I've been reading a lot on this forum learning new stuff as I go!

So far I have build my base and concrete hearth, I'm planning a 30" diameter dome 16" or so height with the relative sized opening blar blar. Anyways after some weeks it's coming on nicely but this is the first time I've built anything ever so I'm learning from my mistakes as I go.

One thing I don't want to cock up is my insulation layers. I'm pretty sure I've got the dome insulation situation nailed but I'm at the stage of pouring my 4" perlite or vermiculite mix insulation layer.

So my main question is which is better/easy to use/more durable/cheaper vermiculite or perlite mix (assuming 5:1 cement mix)?
I understand they both have the same insulating properties.

My progress so far can be seen here:
Mike Suttie's Photos - Pizza Oven Construction!!! | Facebook

Cheers guys
Reply With Quote
  #2  
Old 06-01-2010, 12:27 PM
SteveP's Avatar
Apprentice
 
Join Date: Oct 2008
Location: Port Saint Lucie, FL
Posts: 114
Default Re: Vermiculite vs perlite for insulation under the oven floor

I didn't use vercumilite or perlite for the floor insulation; I used a 2" ceramic insulation board. I did put a 4" dome insulation of perlite and portland cement on the oven. I read on one of the posts that perlite will break down more than vermiculite during mixing, but I don't know how it differs from vermiculite as far as compressive strength is concerned once mixed and cured. Perlite was more readily available than vermiculite and was about $2.25 USD per cu ft.

Your build is looking good.
__________________
My WFO project:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #3  
Old 06-01-2010, 12:55 PM
Raffy's Avatar
Apprentice
 
Join Date: Sep 2008
Location: Philippines
Posts: 213
Default Re: Vermiculite vs perlite for insulation under the oven floor

From what I have observed from the two, there is really not much difference in performance. I was a bit surprised with the perlcrete's compressive strength considering how light perlite was (using 5:1 ratio). Like most people, you can tell when the perlite is properly coated with cement better than vermiculite since perlite is white. You can go with higher ratios like 8:1 or even 10:1 to increase insulation performance without suffering much loss in compressive strength. You do suffer in terms of bond strength. The perlcrete is like rice crispies and the grains chip off easily at higher ratios. I applied a concrete border to the sides of the insulating perlcrete to keep it from crumbling.

I think your decision will be based more on the availabilty and price in your location. But if you have money to burn, I suggest you go for the more high tech insulation boards. They are much more efficient and less messy to install.
__________________

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #4  
Old 06-02-2010, 02:08 AM
Peasant
 
Join Date: May 2010
Location: High Wycombe, UK
Posts: 34
Default Re: Vermiculite vs perlite for insulation under the oven floor

Awesome thanks for your response. Yea I was wondering about the compression strength given how light that stuff is! I was looking at Perlite and it's dirt cheap but I really don't want my oven raised by another 4" so may have to invest in 2" of ceramic board stuff like you say.

"Your build is looking good."
Cheers Steve! Although this is my first building experience ever so it is far from elegant! The next one will be something special haha.

Cheers for your help guys
Reply With Quote
  #5  
Old 06-02-2010, 02:42 AM
david s's Avatar
Il Pizzaiolo
 
Join Date: Mar 2007
Location: Townsville, Nth Queensland,Australia
Posts: 4,518
Default Re: Vermiculite vs perlite for insulation under the oven floor

Raffy,
excellent post. This one should have been in bold.The perlite is marginally better in insulation value , but is trickier to handle (dust and abrasion degradation) I prefer vermiculite.
Reply With Quote
  #6  
Old 06-02-2010, 03:39 AM
FIREANDFLAMES's Avatar
Apprentice
 
Join Date: Mar 2008
Location: EDSON, ALBERTA, CANADA
Posts: 104
Default Re: Vermiculite vs perlite for insulation under the oven floor

Quote:
Originally Posted by mikesuttie View Post
So my main question is which is better/easy to use/more durable/cheaper vermiculite or perlite mix (assuming 5:1 cement mix)?
I made a 4" thick layer of vermiculite and mixed it 7:1, after the third day i was worried about the strength of it because i could press it down quite abit. After about a week it became really hard.
Reply With Quote
  #7  
Old 06-02-2010, 07:32 AM
Peasant
 
Join Date: May 2010
Location: High Wycombe, UK
Posts: 34
Default Re: Vermiculite vs perlite for insulation under the oven floor

After enquiring about the CF board stuff it really is going to push my budget over the top plus i'll need it cut delivered etc so looks like i'll have to modify my design a bit and get some perlite.

Ok this may sound stupid but is the 5:1 ratio done by mass or by say heaped quantity(shovel load!) I.e for every kg of cement it's 5 kgs of perlite ??
Reply With Quote
  #8  
Old 06-02-2010, 09:36 AM
Derkp's Avatar
Apprentice
 
Join Date: Apr 2010
Location: Utah
Posts: 188
Default Re: Vermiculite vs perlite for insulation under the oven floor

Hi,

I just finished my insulation layer, I had a one gallon bucket and a 2 gallon bucket and used about a 6 to one ratio. 3- 2gallon buckets of perlite to 1 gallon bucket of portland cement. I folded the dry together and then folded in the water gently. I made relatively small batches 6 gallons of perlite and one gallon of cement. It has been two days and it is setting up well. Wear mask while mixing, a little dusty.


Derk
Reply With Quote
  #9  
Old 06-03-2010, 02:54 AM
Peasant
 
Join Date: May 2010
Location: High Wycombe, UK
Posts: 34
Default Re: Vermiculite vs perlite for insulation under the oven floor

Cool sounds good Derk! How long will you give it before building on top of it?? God I really want to get my dome built!! Will have to keep myself occupied with rendering (stucco or whatever you guys call it! lol) the walls while I wait for perlite mix to set.
Reply With Quote
  #10  
Old 06-03-2010, 08:18 AM
Neil2's Avatar
Il Pizzaiolo
 
Join Date: Oct 2006
Location: Vancouver Island
Posts: 1,374
Default Re: Vermiculite vs perlite for insulation under the oven floor

Ok this may sound stupid but is the 5:1 ratio done by mass or by say heaped quantity(shovel load!)

By volume. Five shovels of vermiculete/perlite to one shovel of portland cement. Water volume as required. (Exact water volume cannot be specified since it may vary depending on relative humidity and any existing water that may already be in your perlite.)
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Why Italian Wood-Fired Ovens are Round james Newbie Forum 50 04-01-2014 09:14 PM
Cast Oven on Trailer Questions djag12 Other Oven Types 49 09-19-2010 07:03 PM
Oven Floor and Vent Layout DimTex Getting Started 1 07-29-2009 12:06 PM
I want to cast my oven floor mikeye15 Pompeii Oven Construction 0 05-17-2009 09:44 PM
Ferro Cement Pizza Oven cvdukes Introductions 20 10-25-2008 09:38 PM


All times are GMT -7. The time now is 07:20 PM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
2006/10 Forno Bravo, LLC