#1  
Old 05-31-2012, 06:23 PM
Serf
 
Join Date: May 2012
Location: VA, USA
Posts: 5
Default First earth oven build

I've been doing a lot of reading, watching, calculating, etc., and am about ready to start my first earth oven build. Of course, each time I learn something new I also think of a new question. Here are some of my current ones, hoping someone might be able to answer:

1. I've seen where people are putting a final coat/seal on their ovens, but I thought I read that it needs to be breathable, and figured a sealant would stop that. Am I missing something?

2. Trying to figure out the best way to construct the mouth. I think I may go with a simple brick structure, but can decide between an arch and a square one using one of the metal right angle things. I saw in one place that a person's arch had begun to sink; is this common? Would using mortar for this step prevent this (I think cob is more common between the bricks)? If using a square design and bracket, do people cover the metal bracket? I figure they must, or else it would look pretty bad, but couldn't find a good image/description of how.

3. Happened to see a youtube video in which the oven was built on top of a stout wooden square frame/table. Is this really possible? I figure that you could make a good 6" or more base for insulation, and leave some extra room around the edges so the wood didn't heat up too much. I know part of the beauty of these is the stone base, but really, if this were on locking casters, I could get it out of the weather without having to build a roof (which the wife doesn't want, and I admit it would break up the patio a bit).

Well, that got a bit long, but I'm trying to think of everything before I'm actually knee deep in mud.
Thanks for the help and all the inspiration around here!
Brian
Reply With Quote
  #2  
Old 06-16-2012, 09:40 PM
cobblerdave's Avatar
Il Pizzaiolo
 
Join Date: Jan 2010
Location: brisbane australia
Posts: 2,434
Default Re: First earth oven build

Gudday
Firstly I'd better tell you I have a WFO built of forno plans but like you I did a lot of reading before that.
Waterproof a clay dome.... Yes it is possible. the main problem is that the cement render will crack with the expandtion of the dome. a way around this is to use ceramic blanket and render over the top. the blanket will be a cushion.
a cheaper option ( yes I have seen this used on a brick oven) Is to firstly cover with an insulating layer of clay and chopped straw then use domestic insulation then chicken wire and render.....be warned only use the "rockwool" after a fireproof insulation layer it will melt as its to hot against the dome.
Building an arch... My first attempt was a failure but I finally finished my oven with a simple arch in front. I used payers cause there only 50mm (2in) thick and allows smaller mortar joints. Build yourself a guide using two bit of Ply or chipboard the shape of the inside of you arch. Screw a couple battons of wood to the first then screw the secound on that. Using a saw set to the thickness of the material cut both in half. Now you have the battens hold the form together and it a simple matter of unscrewing the form apart to make it easy to remove from your completed arch. To make you arch strong you dont need any mortar on the inside edge of the pavers only the outside thicker part of the joint in this way each of the individual payers is resting on the next not on the soft mortar.
Makeing it movable.. well of course its possible whatever you build is quite a lot of mass not easy to move even on a flat surface. this link might help
http://www.fornobravo.com/forum/f43/...els-16229.html (Oven on wheels)
Finally a good read would be Allan Watts book "build your own wood fired oven" It has no plans as such but explains how to build a cob, a cast and a brick oven. Rosenberg Publishing

Regards Dave
__________________
Measure twice
Cut once
Fit in position with largest hammer

My Build

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

My Door

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Oven Curing james Firing Your Oven 335 07-15-2014 07:12 PM
Preparing for steel oven build. scarnucci Other Oven Types 31 07-06-2014 11:39 AM
Two tiered ovens? Safety? and Quickest time to build a pizza oven. jeanine Getting Started 7 06-04-2012 02:41 AM
My portable tandoor oven build voon Other Oven Types 6 12-07-2010 10:33 AM
Rookie Oven Build in Delaware Behen Pompeii Oven Construction 14 07-26-2010 06:39 PM


All times are GMT -7. The time now is 08:20 PM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
2006/10 Forno Bravo, LLC