#1  
Old 06-29-2008, 12:56 PM
Serf
 
Join Date: Jun 2007
Location: Columbia, South Carolina
Posts: 24
Default Thinking of Casting

I'm thinking about casting my oven with a product called Kaocrete. The manufacturer is only 45 mins from me so I wouldn't have to pay shipping. It's only about $25 a bag. My only question is whether or not it would be a good product to use based on it's content. The alumina is 47% and the silica is about 40%. The technical sheet can be found here for all of the kaocrete products. http://www.thermalceramics.com/upload/pdf/314-105.pdf

Thanks,


Tony
Reply With Quote
  #2  
Old 06-29-2008, 04:03 PM
Master Builder
 
Join Date: Mar 2008
Location: Washington State USA
Posts: 768
Default Re: Thinking of Casting

As long as you have access to a kiln large enough to properly fire the cast WFO or a plan for doing it (ie: home made brick kiln, wood fired or whatever) I'd give it a try. I've built small furnace's using similar materials but upon recommendation of AP Green I designed my furnaces such that each piece could fit into a pottery kiln that was available to me and be fired at proper temperatures under controlled conditions. Not saying you couldn't cast one, cure it and burn it in the middle of a bonfire and not have it come out OK. If you have a couple of hundred bucks to venture and the time... I'd go for it.

But then consider the source... I'm the guy building a WFO around a steel dome :-)

Wiley
Reply With Quote
  #3  
Old 07-11-2008, 02:35 PM
enz enz is offline
Peasant
 
Join Date: Dec 2006
Location: San Jose, CA
Posts: 41
Default Re: Thinking of Casting

aferaci,
I cast a 42" Low Dome about a year ago from Mizzou Castable from Harbison Walker. I chose this material since it matched both the thermal mass and conductivity of fire brick. I posted a series showing the male molds I used right after I finished it, in Tools, Tips and Techniques, I assume it's still back there.

After something like 25 firings, what did I learn?:

The dome needs to be cast in ONE pour. You will get fine cracks where the pours meet. You will need an external mold as well. We tried to work our way up the molds without one and failed miserably. You only need a mold about 2/3's of the way up, after that you can just mound it. These cracks don't seem to affect performance or strength (I've jumped on the dome).

Cure slowly and steadily just like everyone else. You need to hit a certain temperature to achieve maximum strength. For the mizzou it was 1250 F. Once you do your perlcrete or other insulation you should have no problem hitting that with hardwood. I hit 1600 interior temp, so the outside probably hit 1250.

Most of all go for it. It is far better to have a pizza oven than to go without!

Enz
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Casting? Kosmo's Q Tools, Tips and Techniques 23 08-07-2008 10:52 PM
casting a vent to anchor plate transition waynebergman Pompeii Oven Construction 7 10-12-2007 11:13 AM
Vent Casting swripley Newbie Forum 3 07-02-2007 05:55 PM
Casting vent wlively Pompeii Oven Construction 29 03-30-2007 07:17 PM
Casting my first oven. Help sonomacast Newbie Forum 0 08-14-2006 12:39 PM


All times are GMT -7. The time now is 03:31 AM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
2006/10 Forno Bravo, LLC