#1  
Old 08-15-2005, 09:35 AM
Marcel's Avatar
Journeyman
 
Join Date: Aug 2005
Location: Oregon
Posts: 426
Unhappy Testing using Attachments to post photos #02

This is just a test to see if using Attachments and drawing images from MyDocuments will allow me to post viewable photos. If you see an image or a thumbnail of an image, it is the basic framing of my earth slab. No alignment has yet been done.

Since the 10 x 10 foot slab is larger than the Hearth Slab to be sitting on the block wall stand, I would like to slope only that front section of the earth based bottom slab to prevent water from entering the storage section.

I could cut about an inch off the facing 2x6 and slope the two neighboring ones to follow that slope but I'd like to retain the 2x6 profile so that they can be used as forms for the Hearth Slab. I have virtually no experience in pouring or sloping part of a slab ( Not the part the block walls sit on ).

If anyone has an idea on how to effect that slope without cutting the 2x6s pleas let me know.

Now let's see if I can post an Attachment:

Nope. My file is 1.24MB but Max. size is 97. KB
[img]images/icons/icon9.gif[/img]

(M) So I went to PictureIt Publishing and tried to save that image as a smaller file. Let's try one more time as 25KB file.
Attached Thumbnails
Testing using Attachments to post photos-still-smaller-image-size.jpg  

Last edited by Marcel; 08-15-2005 at 09:50 AM. Reason: Image size too large; now reduced?
Reply With Quote
  #2  
Old 08-15-2005, 09:44 AM
james's Avatar
Brick Oven Merchant
 
Join Date: Mar 2005
Location: Pebble Beach, CA
Posts: 4,648
Default

Do you have a photo software package that will reduce the size of the photo?

James
__________________

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #3  
Old 08-15-2005, 01:16 PM
Robert Musa's Avatar
Apprentice
 
Join Date: Mar 2005
Location: Sacramento CA
Posts: 116
Default

several months after completing my oven, i realized that i was storing a fair amount of water along with the wood underneath the oven. so i simply cleaned the storage area out, went to home depot, bought a couple of bags of grout, placed a board in front of the hole to the entry area and sealed it to the patio with masking tape, mixed the grout to milkshake consistency and poured the grout into the storage area (the board blocked the grout from flowing out). this raised the floor level of the storage area to about 1/2 to 3/4 inch above "sea level". if you push the bulk of the grout towards the back you can get a primitive "slope" as well. (btw, this would have been easier if i would have done it before pouring the hearth).
__________________
my site for our pompeii and tandoor ovens

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #4  
Old 08-15-2005, 06:12 PM
paulages's Avatar
Journeyman
 
Join Date: May 2005
Location: portland, or
Posts: 292
Default

when you are screeding your concrete, you could scrape some concrete away where you want your low point to be, and just manually slope where your entrance will be. by using a smaller screed (rather than using one that will glide all the way across the entire frame) you can smooth the sloped area below the level of the frame.
__________________
-paul
overdo it or don't do it at all!
Reply With Quote
  #5  
Old 08-15-2005, 08:36 PM
Marcel's Avatar
Journeyman
 
Join Date: Aug 2005
Location: Oregon
Posts: 426
Default Thanks: James, Robert, and Paul

Thanks, James for the idea of using a software program to reduce the image. It worked!

Thanks to both Paul and Robert for their ideas to provide a slope.

Robert, if I go with your idea, I would definitely pour mortar, inside the concrete block walls before the hearth slab work begins. That way I don't even need to have a step but should be able to feather the leading edge.

Paul, I'm a bit unsteady so having no support for the narrower screed may be too challenging for me; though a skilled mason surely could pull it off.

You may all be chuckling that I have not even commenced the pour but thanks to all the feedback I've had on anticipating possible problems, I feel I entered this Forum not a day too soon! I'm sure that even you Pros have benefited from input prior to your actual work on a given phase.

Thanks and you'll be getting on-going questions from me.

================================================== =

An overdue response from me to whomever (Jim? James?) thought I'd be paying an arm and a leg to have the concrete for the earth slab delivered; I got a quote, which follows:

Hello.

The total price would be $223.00 - here's the breakdown:

2 yards at $79 = $158.00
Short rate = $ 50.00
Mileage = $ 5.00
Fuel Surcharge = $10.00

Total: $223.00

(M) That is certainly more than renting a mixer and buying ready mix, but at around $2 for a 60 Lb. bag and considering my age and the effort to mix so many bags, I looked at the $223 as a reasonable extravagance for me, as the whole project may end up costing $1,500.
Reply With Quote
  #6  
Old 08-24-2005, 12:40 PM
Marcel's Avatar
Journeyman
 
Join Date: Aug 2005
Location: Oregon
Posts: 426
Default

This was just a test to see if using Attachments and drawing images from MyDocuments will allow me to post viewable photos.This is the basic framing of my earth slab. No alignment has yet been done.

Because I would like to slope only that front section of the earth based bottom slab to prevent water from entering the storage section I will use Robert Musa's idea of pouring mortar on sloped screeds placed inside the wood storage are, after the Hearth Stand Blocks are set up.

Now let's see if I can post another Attachment:
Max. size is 97. KB

So I went to PictureIt Publishing and tried to save that image as a smaller file.

The next image should show Mary's floor plan for our realtively larger 10' x 10' slab, still not yet poured! The icons are not to scale. The area to the right of the oven proper is to be a work table, made of masonry.

I hit upon the idea of bringing in water and electrical. Subsequesnt photos will show the set-up in greater detail.

If you see pencil lines they are there because I initially forgot to allow about 4" for a faux rock facade on the hearth stand. We hope to include 2 Elec. outlets, a sink and water supply for the adjacent work table. Setting the feeds to enter the concrete blocks was a meticulous measuring task which I hope will be successful.

Thanks,

Marcel


Attached Thumbnails [img]attachment.php?attachmentid=95&stc=1&thumb=1[/img]
Attached Thumbnails
Testing using Attachments to post photos-marys-oven-layout-floor-plan-4  
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 12:03 AM.

Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
2006/10 Forno Bravo, LLC