My Old Kentucky Dome

[asudavew]

Originally Posted by Acoma

Dannyboy, go to Ken's Picasa album. There, you will see the compoud miter they are referencing.

Harbor Freight Tools - Quality Tools at the Lowest Prices


This is the link to the saw most people are using. After my experiences, if you can afford it. Grab it!

[Dannyboyblue]

Thanks, Acoma & asudaveasudavew. But I'm still baffled. The saw looks like it's not adjustable enough to do the precise cuts that some of you have been doing. It has a 45 degree miter fixture, but what do you do if you need a 12 degree cut?

[Acoma]

Dannyboy, Les and Ken will likely respond today with how to handle that. Others may as well. Hang tight.

[asudavew]

I am not positive, but I believe they use shims to hold the bricks at the appropriate angles. Like under one side to hold part of it up.

[Two Dog's Brewing]

Ken finally the answer I was looking for I was looking for a pattern or something and never say anything. I notices some people dont taper the the soldiers. I really like the look of that!.

Ok so you can cut a bunch of bricks the same with a jig right? I would guess that each course has a unique shape and unigue only to its respective course. I know there will be a bunch of custom bricks but with that answer I am getting ready.

Thanks all

[dmun]

Originally Posted by Dannyboyblue

I'm still baffled. The saw looks like it's not adjustable enough to do the precise cuts that some of you have been doing. It has a 45 degree miter fixture, but what do you do if you need a 12 degree cut?

It's true. A sine-plate like attachment would be a really good accessory to the HF wet saw. I made a fixed sloping attachment I bolted to the table for the many 7 1/2 degree cuts needed for my bricks. You can mark the angle needed with a protractor, and hike the brick up with a block of wood. You'll also get really good at freehand cuts with a little practice - that's how I cut all the complicated shapes needed to transition from the dome to the flue. Just make sure you have the smooth diamond blade rather than the segmented one if you are going to get up close and personal to it.

[Ken524]

Originally Posted by Dannyboyblue

But I'm still baffled. The saw looks like it's not adjustable enough to do the precise cuts that some of you have been doing. It has a 45 degree miter fixture, but what do you do if you need a 12 degree cut?

Danny,

Sorry for the confusion. I don't have a compound miter saw, just the plain old simple Harbor Freight saw.

What I was trying to say is that I am making cuts like those you would easily make with a compound saw.

To make these types of cuts with the HF saw, you have to use clamps, scraps of brick, wood or whatever to position the brick exactly where you want it on the table. Once you have it set up, you can mass cut bricks.

A true compound brick saw would be wonderful for this!

[Dannyboyblue]

No problem and thanks for the clarification. I suppose that a compound brick saw doesn't exist. At least I haven't found it. So I'm wondering what would be better (easier/faster/safer) in the long run cutting dry with a dual compound miter saw or fiddling with wedges and shims with the hf wet saw?

Also Dmun, can such an attachment as you showed be put on or was that just theoretical?

[Les]

Danny - go with the wet saw. It's really not that hard to get a close enough cut. You don't want to be anywhere near the amount of dust a dry blade is going to kick out.

Les...

[asudavew]

Originally Posted by Les

Danny - go with the wet saw. It's really not that hard to get a close enough cut. You don't want to be anywhere near the amount of dust a dry blade is going to kick out.

Les...

I second that ! I dry cut my whole floor and some halves... Messy work.. If I had a do over... I would of waited and saved for the HF saw!