web analytics
Concern about mold - Forno Bravo Forum: The Wood-Fired Oven Community


1 of 2 < >

Forno Bravo Forum Thread Message

Hello, Forno Bravo Community Forum Members!

The Forno Bravo team has heard the feedback in regards to the community forum. We wanted to take the time to re-enforce our commitment to a fully engaged Forum with professional moderation.

Our top priority as a company is to fix all forum errors and issues that you are experiencing. As we are swiftly working on these problems, we want to say that we highly value the Forum Bravo Community Forum and every single community forum member.

We have set up this thread so that every member can address any concerns, issues and questions about the forum. Please feel free to ask whatever you would like in regards to the forum; let us know what issues you are experiencing so we can work on resolving them as fast as possible. However, we stress that we would like constructive engagement, so please be specific about the issue you are experiencing.

Thank you for all of your patience and continued support.

Link to topic: http://www.fornobravo.com/community/...with-new-forum
2 of 2 < >

Dome Installation Video - Casa / Premio / Modena


For many of you who bought a modular oven, you may have asked how we put the domes together when we build them. For those of you considering one of our ovens, we shot a video to make your install easier.

Check it out on our You Tube Channel.


If the link doesn't work, simply go to You Tube and type Forno Bravo Channel. The video title is How to Set your Forno Bravo Oven Dome Pieces.

Thanks for participating in our Forum. We will have more video content available soon.
See more
See less

Concern about mold

  • Filter
  • Time
  • Show
Clear All
new posts

  • Concern about mold

    As I have been building my oven in the damp northwest (especially the fall and winter), I have already had mold issues in that my masonite arch forms have become quite fuzzy. I imagine that the rather damp plywood that has been the floor protection for the last four months is probably pretty moldy too, but I'm not too worried about it since the inside of the oven is going to be virtually sterlized anyway.

    What I am a little concerned about is the fluffy InsWool insulation. I'm not using a blanket, I'm using loose "bulk" (with some sort of wire mesh to hold it in place, I haven't quite figured this out). I'm worried that it will become damp and totally run through with mold before I get a chance to fully enclose it, either in a vermicrete dome or in a "building" subsequently filled with loose vermiculite.

    Any thoughts on this? Does it not matter if it gets totally moldy before I put it a vermicrete dome over it? What if I do the building, roof, and loose vermiculite? In that case it is never truly sealed and will almost certainly be damp forever, or every winter.

    Website: http://keithwiley.com
    WFO Webpage: http://keithwiley.com/brickPizzaOven.shtml
    Thread: http://www.fornobravo.com/forum/f21/...ttle-7878.html

  • #2
    Re: Concern about mold

    As a fellow resident of the Pacific Northwest I am familiar with the mold/algae/fungus growth of which you speak. I suspect that the insulation is inorganic (ie akin to spun ceramic... kaowool), if kept clean such are not a food source for such organisms. Yes, lichen grows on barren clean rock but hopefully you will finish before that occurs. Lichen feeds on rock decomposing into dirt, primarily feldspar into clay minerals if I remember correctly something I once read and that takes significant time.

    All that being said I would endeavor to keep it as dry as possible at the same time trying not to create an environment condusive to growth. A plastic sheet might seem ideal until on a hot day you get condenstion and higher temperatures from the greenhouse effect of the plastic sheet. I have friends who have air dried wood successfully out-of-doors by good airflow and space between the weather proof layer and the top layer of wood. And of course "ricking" the layers of wood.

    Rainwater being a "scrubber" of the air it falls thru is not clean at all and should you get the insulation soaked thru with rain water I would (personally if it were mine) give the whole a good spraying with a clorox water solution. I'm saying "soaked" not "dampened". If soaked wouldn't be any wetter and by doing so it at least wouldn't be growing anything.

    Glass blower friends have told me that typically they wet kaowool with water before working with it to keep the errant broken fibers from becoming airborne. That may be fine but then one must dry it out which again takes time. I'm not familiar with the insulation you are using, is it hollow tubes (like fiberglass insulation) or solid strands (like kaowool)? Once wet fiberglass will never fully dry out as the tiny tubes suck water thru capilary action (which then becomes trapped).

    In the end it probably doesn't matter much if it gets a little bit moldly, your "totally run thru with mold" would be something I would do alot of work to avoid.

    Hope this has helped,


    • #3
      Re: Concern about mold

      No structure can be made absolutely waterproof. Design your enclosure so that there is reasonable ventilation to enable the insulation layer to dry out if water gets in.

      With an enclosure, you can skip the wool insulation or blanket . Just use straight vermiculite.


      • #4
        Re: Concern about mold

        I'll take all of that under advisement. I'm still trying to figure out how to build a "building", walls and roof.


        Website: http://keithwiley.com
        WFO Webpage: http://keithwiley.com/brickPizzaOven.shtml
        Thread: http://www.fornobravo.com/forum/f21/...ttle-7878.html