web analytics
I made a tool - Forno Bravo Forum: The Wood-Fired Oven Community

Announcement

Collapse
1 of 2 < >

I'm Peter Reinhart! Ask Me Anything! Monday, February 15, 2016 7:00-8:00 pm EST

To kick off our AMA feature, we have invited author, chef and master bread maker and host of Pizza Quest, Peter Reinhart, to be our first host! Peter will be in the Forum on Monday, February 15th, from 7:00 - 8:00 pm EST. If you are unable to be online during the live session, you can post your questions in the sticky post. Peter will answer those questions during the live session on February 15th. You can view Peter's answers to your questions as well as what happened during the live session in the session thread.

Ask Me Anything New Forum Feature

You will notice a new forum at the top of the main page called, "Ask Me Anything". This forum will be used for live one hour "Ask Me Anything" (AMA) sessions hosted by people who are knowledgeable in different areas pertaining to wood fired ovens. How it works:
- Each AMA will have a "sticky" thread where the community can post questions they would like answered during the live session. This will allow everyone to participate even if you can't be online for the live session. These questions will not be answered by the host until the live AMA; if you need an answer quickly, you should post it in the appropriate Forum area for the community to respond.
- Another thread will be posted for the live AMA. Registered users who are logged in during the live session can interact with the host by asking questions and receiving responses.
- The live thread will remain in the AMA forum to view after the session.

We hope you enjoy this new feature! Please let us know if there is a topic that you'd like to have as an AMA and we'll look for a host!

Forno Bravo
2 of 2 < >

Dome Installation Video - Casa / Premio / Modena

Hello,

For many of you who bought a modular oven, you may have asked how we put the domes together when we build them. For those of you considering one of our ovens, we shot a video to make your install easier.

Check it out on our You Tube Channel.

https://www.youtube.com/watch?v=-7q7...jSniYogfUra06Q

If the link doesn't work, simply go to You Tube and type Forno Bravo Channel. The video title is How to Set your Forno Bravo Oven Dome Pieces.

Thanks for participating in our Forum. We will have more video content available soon.
See more
See less

I made a tool

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • I made a tool

    I was having problems using a flat hoe to clean coals from a round oven. I bought a flexable replacement steel floor scrapper blade - 18 inches X 5 inches and bent it to the inside diameter of my oven. I then welded several rods to secure the curve and provide a method of inserting it into an 8 ft piece of pipe.

    I made it about 2 months ago and use it at every firing. I have been looking for any problems with it, but so far, no problems identified.

    The welded rod should be as far back from the ends as possible so that it can reach behind the vent opening.

    Tool number 2 is a pizza turning peel. I made this because the 8 inch diameter peels were just a little small to fit under some of my larger pans. It is made from 22 gauge steel. It was cut from a 12x18 in piece and I got two 9 inch diameter peels from it.

    I slit a pine pole 5 ft long to accept the metal tang, drilled two holes 1/4 inch and bolts to match - cut and fit.

    Larger diameter pole make it easier to handle and twist.

    Tools were metal bladed jigsaw, tin snips, compass, drill, 1/4 inch metal bit (goes through wood also) ear and eye protectors. Etc, etc
    Last edited by navyintel; 12-18-2012, 10:52 AM.

  • #2
    Re: I made a tool

    Obviously Navy Intelligence hard at work here. I like your solution
    Kindled with zeal and fired with passion.

    Comment


    • #3
      Re: I made a tool

      Hi Smartnavyguy,

      Simplify your design, and market it. I will buy two(2).

      Comment


      • #4
        Re: I made a tool

        Wow, two replys so quick. I will leave marketing to more adventurous people than me.
        As for Navy Intelligence-long retired (7 years) and better forgotten.
        If you are interested, I have a pinterest site-also under navyintel - one of my hobbies is bone carving, so take a peek also I have more pics of the WFO build. More tools to follow.

        Comment


        • #5
          Re: I made a tool

          How do I get to this site?

          Comment


          • #6
            Re: I made a tool

            Michael L (navyintel) on Pinterest

            http://pinterest.com/navyintel/
            Last edited by navyintel; 12-16-2012, 08:14 PM. Reason: more info

            Comment


            • #7
              Re: I made a tool

              I was reluctant to open this string called "I made a tool"....didnt need to see pictures of someone's "tool"

              Comment


              • #8
                Re: I made a tool

                I added another tool to the top of the string. I explained how I made.

                ML

                Comment

                Working...
                X