web analytics
mortar and cold temps - - Forno Bravo Forum: The Wood-Fired Oven Community


1 of 3 < >

Forum Page Loading Response

Forum Members:

We have received feedback regarding recent issues with page loading response time. We believe the slow response issue stems from the analytics we added with the new Forum. We are in the process of reconfiguring those elements and, after an approximate 24-hour time period for the reconfiguration to run, we anticipate a return to normal page load times. Thank you for your patience!
2 of 3 < >


Hello, Forno Bravo Community Forum members.

As many may have noticed already, the Community Forum site was briefly down today. While working on scheduled routine maintenance, we encountered an error when trying to add a software update. As the site is now back up and running, some of you may notice that some recent data has been misplaced from November 10th up to today. We are currently working on resolving the issue. The forum has full operational capabilities and we encourage all forum members to continue actively posting in the threads.

We apologize for any inconvenience that this issue may have caused you. The Forno Bravo family values each and every member of our community. If you have any issues or concerns, please feel free to let us know on our issues thread here:


Thank you for understanding.
3 of 3 < >

Forno Bravo Forum Thread Message

Hello, Forno Bravo Community Forum Members!

The Forno Bravo team has heard the feedback in regards to the community forum. We wanted to take the time to re-enforce our commitment to a fully engaged Forum with professional moderation.

Our top priority as a company is to fix all forum errors and issues that you are experiencing. As we are swiftly working on these problems, we want to say that we highly value the Forum Bravo Community Forum and every single community forum member.

We have set up this thread so that every member can address any concerns, issues and questions about the forum. Please feel free to ask whatever you would like in regards to the forum; let us know what issues you are experiencing so we can work on resolving them as fast as possible. However, we stress that we would like constructive engagement, so please be specific about the issue you are experiencing.

Thank you for all of your patience and continued support.

Link to topic: http://www.fornobravo.com/community/...with-new-forum
See more
See less

mortar and cold temps -

  • Filter
  • Time
  • Show
Clear All
new posts

  • mortar and cold temps -

    I'm sure this question has been brought up before but I'm going to ask anyway:
    Will below freezing temps matter for bricks just laid? We put a light in there and covered it with a few big cloths and a tarp. Is that a good thing or a bad thing?
    It won't heat it up too much, will it?

    The low tonight is supposed to be 31.


  • #2
    Re: mortar and cold temps -

    A light is no where close to causing a problem. DON'T LET IT FREEZE. It will turn concrete to crap.

    Check out my pictures here:

    If at first you don't succeed... Skydiving isn't for you.


    • #3
      Re: mortar and cold temps -

      I have asked a similar question. I have been told that freezing temps and proper curing do not go together. That being said if you use tarps and cloths and low is only 31 the brick you just laid may not see freezing temps. I have also asked about using some sort of additive during freezing temps. This was not recommended because there is no such thing as antifreeze just accelerators to speed the curing process and these have the potential to weaken the structure.
      Thread: http://www.fornobravo.com/forum/f8/g...land-8759.html

      Member WFOAMBA


      • #4
        Re: mortar and cold temps -

        My oven will not be completed before the "deep freeze". Should I be concerned about freezing? I'm probably done until the spring. I haven't worked on it in three weeks so I'm assuming there shouldn't be an issue with freezing temps...

        My Oven Progress: http://www.fornobravo.com/forum/f8/p...uild-7155.html

        If you fail to plan, you plan to fail!