web analytics
Draft basics? - Forno Bravo Forum: The Wood-Fired Oven Community

Announcement

Collapse

I'm Peter Reinhart! Ask Me Anything! Monday, February 15, 2016 7:00-8:00 pm EST

To kick off our AMA feature, we have invited author, chef and master bread maker and host of Pizza Quest, Peter Reinhart, to be our first host! Peter will be in the Forum on Monday, February 15th, from 7:00 - 8:00 pm EST. If you are unable to be online during the live session, you can post your questions in the sticky post. Peter will answer those questions during the live session on February 15th. You can view Peter's answers to your questions as well as what happened during the live session in the session thread.

Ask Me Anything New Forum Feature

You will notice a new forum at the top of the main page called, "Ask Me Anything". This forum will be used for live one hour "Ask Me Anything" (AMA) sessions hosted by people who are knowledgeable in different areas pertaining to wood fired ovens. How it works:
- Each AMA will have a "sticky" thread where the community can post questions they would like answered during the live session. This will allow everyone to participate even if you can't be online for the live session. These questions will not be answered by the host until the live AMA; if you need an answer quickly, you should post it in the appropriate Forum area for the community to respond.
- Another thread will be posted for the live AMA. Registered users who are logged in during the live session can interact with the host by asking questions and receiving responses.
- The live thread will remain in the AMA forum to view after the session.

We hope you enjoy this new feature! Please let us know if there is a topic that you'd like to have as an AMA and we'll look for a host!

Forno Bravo
See more
See less

Draft basics?

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Draft basics?

    Hey guys trying to get ready to design vent size. I'm pulling off of memory but I think I read you get the best draft from going large to small areas. Is that correct. Because I'm so tight I will only be able to brick the inner arch. From ther I have to pour the front arch. The poening is 20" so i was thinking 20" wide x 4" deepx 6" tall. From there taper to a n 8" wide x 4" deep to set the anchor plate. Does that sound like I'm the right track.
    Thanks,
    Mike

  • #2
    Re: Draft basics?

    How big a flue pipe were you going to go with and how big is your oven. If I understood your post correctly you will have 8 x4 opening to set your anchor plate on and this does not sound right.
    I enjoy cooking with wine, sometimes I even put it in the food I'm cooking. --- Julia Child

    http://picasaweb.google.com/mattluttropp

    Comment


    • #3
      Re: Draft basics?

      It would be an 8" round. From pics I see it doesn't look like many are deeper than 8". I would use an ancor plate. I'm casting it.

      Comment


      • #4
        Re: Draft basics?

        mikeye15
        an 8" round flue will be fine for a 42' Pompeii, running off an anchor plate, but I would have that plate as high above your oven openning as practicable to allow the smoke and gasses to flow in the chimney upwards direction than flow straight out your front arch.
        Even if you flattened out the circular flue to a flattened oval, it will still be the same area and should work fine.
        I have an 8" flue but a much wider and deeper and also higher void to direct the smoke out and up.
        Pics on my build, see below.

        Neill
        Prevention is better than cure, - do it right the first time!

        The more I learn, the more I realise how little I know


        Neillís Pompeiii #1
        http://www.fornobravo.com/forum/f8/n...-1-a-2005.html
        Neillís kitchen underway
        http://www.fornobravo.com/forum/f35/...rway-4591.html

        Comment

        Working...
        X