web analytics
How to mesure cuts - Forno Bravo Forum: The Wood-Fired Oven Community

Announcement

Collapse

I'm Peter Reinhart! Ask Me Anything! Monday, February 15, 2016 7:00-8:00 pm EST

To kick off our AMA feature, we have invited author, chef and master bread maker and host of Pizza Quest, Peter Reinhart, to be our first host! Peter will be in the Forum on Monday, February 15th, from 7:00 - 8:00 pm EST. If you are unable to be online during the live session, you can post your questions in the sticky post. Peter will answer those questions during the live session on February 15th. You can view Peter's answers to your questions as well as what happened during the live session in the session thread.

Ask Me Anything New Forum Feature

You will notice a new forum at the top of the main page called, "Ask Me Anything". This forum will be used for live one hour "Ask Me Anything" (AMA) sessions hosted by people who are knowledgeable in different areas pertaining to wood fired ovens. How it works:
- Each AMA will have a "sticky" thread where the community can post questions they would like answered during the live session. This will allow everyone to participate even if you can't be online for the live session. These questions will not be answered by the host until the live AMA; if you need an answer quickly, you should post it in the appropriate Forum area for the community to respond.
- Another thread will be posted for the live AMA. Registered users who are logged in during the live session can interact with the host by asking questions and receiving responses.
- The live thread will remain in the AMA forum to view after the session.

We hope you enjoy this new feature! Please let us know if there is a topic that you'd like to have as an AMA and we'll look for a host!

Forno Bravo
See more
See less

How to mesure cuts

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • How to mesure cuts

    I have decided im going to try and cut the (vertical)sides of the bricks in the oven to avoid getting the wedge shaped mortar lines.
    Im using sand, cement, lime, fireclay mix and will fill the backs of the bricks(top and bottom also) as i dont care what the outside looks like.

    Is there a way to measure the vertical angle on the brick so i can set the saw and cut the whole course the same to get a uniform look?
    Sorry if this question doesnt make sense.

  • #2
    Re: How to mesure cuts

    makes good sense.

    There are some really perfect ovens here - but imperfect ones work quite well, too.

    Many of us used Hendo's dome guage or a variation to help deternine the angle cut required.

    search for it and I think it will give some clarity.

    Good luck!

    Christo
    My oven progress -
    http://www.fornobravo.com/forum/f8/c...cina-1227.html
    sigpic

    Comment


    • #3
      Re: How to mesure cuts

      thanks Christo.
      Ive made a dome guage with a castor and quick clamp to hold the bricks in place. I havent read how to use it for the cuts though. Will have to go back and read the thread.

      Comment


      • #4
        Re: How to mesure cuts

        Ah, i can use the guage to give me the line for the cut. then use the guage to hold/set the brick in place.

        Comment


        • #5
          Re: How to mesure cuts

          The process I finally settled on was to.

          1 cut the bricks, for the course, for max width. This will be the dimension of the bottom outside of the cut brick. I found that I needed a few wider and a few narrower to stagger the joints.

          2 cut somewhere around 3/8ths to 1/2 of an inch off of the front top face of the course bricks. This helps to set the top of the course bricks on plane with the center point of the hemisphere, where your caster is. It also minimizes the amount of grout used on the outside to slope the cut brick. If you use a 10" saw you won't be able to cut completely through the brick, I had about a 1 inch flat area on the top outside of the cut bricks. This created a change in slope from the cut area to the un-cut area on the cut brick. This minor slope change is buried in mortar so no worries here, but it's worth mentioning.

          3 cut the side cuts. These should be on plane with the vertical axis of the dome hemisphere, a vertical line from the caster.

          You could swap the 2 and 3 without issue, but for me this is what I found worked best.

          Also as mentioned above, fit and finish doesn't necessarily affect function, but it does take much more time and more saw blades.


          Chris
          Last edited by SCChris; 09-30-2009, 06:33 AM.

          Comment


          • #6
            Re: How to mesure cuts

            3G

            In addition to the above, because Iím a bit dyslexic, I found that I needed to build a jig that I could use to help with the side cuts. Being dyslexic, I look at these sorts of things different than most people and so donít necessarily recommend that you take the time to build a similar jig, but it might help you to know how I solved this. Look in the tools area and look for ďNew brick cutting tool Ė old cutting tool??Ē. Youíll note that there are specific changes Iíd make to the jig to beef things up and make it more stable, more stable is more safe and faster. Youíll note that I make a point to caution anyone about using this tool, accidents happen in a hurry and accidents with power tools can really make for a bad day in a hurry. If I can help with answers about this, just let me know.

            I also recommend that if you havenít yet, look at Christoís, Dinoís and Lesís builds. Lesís build is unbelievable. Also look for JCG31 and his brick cutting chart, it helped me to verify where I was in the dome build.

            Sincerely

            Chris

            Comment


            • #7
              Re: How to mesure cuts

              thats for the detailed responses guys.
              I suppose i need to work out if i want a thin(maybe 6mm) mortar line around the whole brick or if i want to try and achieve a near mortarless look from the inside. If i go the mortarless look i suppose i would need to cut the bricks slightly more than the guage shows to enable me to get some mortar on the backs of the bricks.

              Comment

              Working...
              X