web analytics
How to fix these problems - Forno Bravo Forum: The Wood-Fired Oven Community



New Forno Bravo Forum Feature

Forno Bravo Forum Community,

You will notice a new forum at the top of the main page called, "Ask Me Anything". This forum will be used for live one hour "Ask Me Anything" (AMA) sessions hosted by people who are knowledgeable in different areas pertaining to wood fired ovens. How it works:
- Each AMA will have a "sticky" thread where the community can post questions they would like answered during the live session. This will allow everyone to participate even if you can't be online for the live session. These questions will not be answered by the host until the live AMA; if you need an answer quickly, you should post it in the appropriate Forum area for the community to respond.
- Another thread will be posted for the live AMA. Registered users who are logged in during the live session can interact with the host by asking questions and receiving responses.
- The live thread will remain in the AMA forum to view after the session.

To kick off our AMA feature, we have invited author, chef and master bread maker and host of Pizza Quest, Peter Reinhart, to be our first host! Peter will be in the Forum on Monday, February 15th, from 7:00 - 8:00 pm EST. If you are unable to be online during the live session, you can post your questions in the sticky post. Peter will answer those questions during the live session on February 15th. You can view Peter's answers to your questions as well as what happened during the live session in the session thread.

We hope you enjoy this new feature! Please let us know if there is a topic that you'd like to have as an AMA and we'll look for a host!

Forno Bravo
See more
See less

How to fix these problems

  • Filter
  • Time
  • Show
Clear All
new posts

  • How to fix these problems

    Greetings. It is getting warmer here on the East Coast. I pulled the tarp off my almost finished oven and am starting a slow warming process.

    I finished the oven itself, but the chimney area was rushed because of the approaching cold weather. We are all very inexperienced, and it was a team effort. Three obvious problems came up with our chimney build.

    1. As you can see from the first photo, the outer arch is very high and large. My limited experience with firing the oven so far suggests that there is a vast amount of heat loss out the front. There is some smoke, but not an overwhelming amount.

    Should I build a second arch below the first to make the outside entrance lower, thereby enclosing more of the chimney area? Most of the ovens I've seen have a relatively low outside opening, though it does tend to be wider than the inside one.

    2. Secondly, I tried in my inexpert way to build some kind of insulation into the break between the chimney area and the oven. Unfortunately I used bricks but out of cal-sil board, and now they are flaking into the oven entry. I assume I need to remove them, or cover them up in some way to prevent flakes from getting into my baked goods.

    What would you suggest?

    3. Last, my chimney seems a bit small for the oven (inside dimensions are 36" x 48"), and I'm wondering if that is why I'm getting smoke out the front. The ceramic flue is an 8 inch square one. I was thinking of adding another length to add area, or perhaps figuring out a way to put a stainless chimney on top of what I have. I will need some kind of cap too. Any suggestions about that problem?

    Given these three problems with the chimney area, perhaps you would recommend that I just cut off the top and start from scratch?

    Thanks in advance for your expert advice.

  • #2
    Re: How to fix these problems

    It appears that you have room to build an arch inside the existing, I would do that and it will probably take care of the smoking, too. For the flaking bricks, I would worry about it until it became a real problem, maybe parge it with refractory.


    • #3
      Re: How to fix these problems

      Originally posted by chickade View Post
      Unfortunately I used bricks but out of cal-sil board, and now they are flaking into the oven entry.
      I'm not sure I understand this. You cut cal-sil into blocks?
      My build progress
      My WFO Journal on Facebook
      My dome spreadsheet calculator


      • #4
        Re: How to fix these problems

        Looking at that last picture, I wonder if you might be able to improve your draw by beveling the edge of the brick supporting your flue pipe to provide an easier transition for the smoke to flow upwards to the pipe. If you have a rotary saw with a diamond blade (e.g. Rotozip or Bosch makes one) or a disc grinder you should be able to do it without too much trouble. Remember it doesn't have to look too pretty because it will be difficult to see and it will get covered in soot anyway.

        If you decide to rebuild (unnecessary IMHO), here's a photograph of what I did by splitting a brick length wise on a diagonal and then putting the two halves together (rotating the top 180 degrees from the other). - Easy to do, almost impossible to describe.