web analytics
Leveling the stand, hearth etc - Forno Bravo Forum: The Wood-Fired Oven Community


1 of 2 < >


Hello, Forno Bravo Community Forum members.

As many may have noticed already, the Community Forum site was briefly down today. While working on scheduled routine maintenance, we encountered an error when trying to add a software update. As the site is now back up and running, some of you may notice that some recent data has been misplaced from November 10th up to today. We are currently working on resolving the issue. The forum has full operational capabilities and we encourage all forum members to continue actively posting in the threads.

We apologize for any inconvenience that this issue may have caused you. The Forno Bravo family values each and every member of our community. If you have any issues or concerns, please feel free to let us know on our issues thread here:


Thank you for understanding.
2 of 2 < >

Forno Bravo Forum Thread Message

Hello, Forno Bravo Community Forum Members!

The Forno Bravo team has heard the feedback in regards to the community forum. We wanted to take the time to re-enforce our commitment to a fully engaged Forum with professional moderation.

Our top priority as a company is to fix all forum errors and issues that you are experiencing. As we are swiftly working on these problems, we want to say that we highly value the Forum Bravo Community Forum and every single community forum member.

We have set up this thread so that every member can address any concerns, issues and questions about the forum. Please feel free to ask whatever you would like in regards to the forum; let us know what issues you are experiencing so we can work on resolving them as fast as possible. However, we stress that we would like constructive engagement, so please be specific about the issue you are experiencing.

Thank you for all of your patience and continued support.

Link to topic: http://www.fornobravo.com/community/...with-new-forum
See more
See less

Leveling the stand, hearth etc

  • Filter
  • Time
  • Show
Clear All
new posts

  • Leveling the stand, hearth etc

    I just poured and checked my slab and to no surprise it is not perfectly level.
    Its not to bad, but not level.
    Now, if I take the time to level out the first course of my bricks for my stand what will guarantee that when I pour the hearth it will be level? Can I just take the time and do whatever is required to level my hearth before I put the super isol on, or should I really take the time to level the stand and level again when I do the hearth?

  • #2
    The hearth is what really matters

    My view is that the hearth is what really matters. If you are a little off level at the foundation slab (some builders put the foundation slab at a slight angle to control water runoff anyway), I would still go ahead and dry stack the concrete blocks, then make sure your forms are dead level when your pour the hearth.

    Would everyone agree with that?
    Pizza Ovens
    Outdoor Fireplaces


    • #3
      1/4" per foot is standard for assuring that water runs in the preferred direction. Something to help keep wood compartments dry seems like a good idea.

      If you're worried about the finished structure being visibly crooked, you could choose to use mortar between the lower courses, making up, for example, 1/4 to 1/2" per course until you get it straight then dry stack the rest. You'd probably want to check with someone who knows regarding how thick and thin mortar joints can be and still cure properly.

      You could also probably offset successive courses slightly in the horizontal direction. If you're off 1/4" per foot that's about 1/6" per 8" block horizontally. The offsets would be covered by your finish material. The horizontal surfaces of the blocks would still be a little off, but you can easily fix that when you pour the hearth slab.


      • #4

        I've poured quite a few foundations over the years, and it's nice when they come out either dead level or sloped to the degree you want. In practice, this rarely happens right on the money. I'd lay out the first course of blocks, then use shims to bring them up to level. Measure how much you're off on this first course, memorize, then lay your mortar bed to make up the difference. I'd use Type S and brick sand, three to one. In reality, if the weather is with you and your mortar is not too sloppy, you will be able to make up, say, half to three-quarters of an inch in the first course. No worries, the mortar will still set up an cure at that thickness. You can even leave brick shims in place in strategic places, mortared down, not dry. As you go up, course by course, you can make up any small error until you reach level. This niggly method will save you a lot of time and hassle at the slab stage. Block is very forgiving in this way, unlike brick. Just make sure to use a block pointer once the mortar sets up but is not dry. This will ensure that your joints are full and tight.

        If you don't have one, buy a line level at HD, line corner blocks (probably have to go to a masonry supply for those), and a good nylon line. Once you're above the first course, set your line level and work too it. Also, a four foot level is a good investment for this sort of work.

        "Made are tools, and born are hands"--William Blake, 1757-1827