web analytics
Moldit-D and Transpiration - Forno Bravo Forum: The Wood-Fired Oven Community

Announcement

Collapse

Photo Galleries are back! Instructions below.

Dear forum users,
Thank you for your patience with the Photo galleries. We've got your galleries online!
We have finished writing a custom script to migrate the PhotoPlog to vBulletin5’s albums.

Unfortunately V-Bulletin killed the "Photoplogs" in their software upgrade which was unforeseen and we're the first development group to have written a script for getting the galleries back... that said, it took some time to reverse engineer the code and get the albums to move over seamlessly!

Forum users will be able to access their “PhotoPlog” images through their user profile page by clicking on the “Media” tab.
They will also be able to browse other albums by going to the albums page. (On the forum site, there is a link in the black bar beside “Forums” to the albums.)

In order for users to create an album please follow the steps below.
1) Go to user profile page and click “Media”
2) Click Add Photos
3) Enter Photo Gallery Title in the first field
4) Click Upload or Select from Photo Album to add photos
5) Click Post
6) Once posted, the album will be created as a “Topic” on the albums page for the public to see. The topic title will be the “Photo Gallery Title” they created before uploading their photos.


To create this migration path we used vBulletin5’s default album structure. Unfortunately, it won’t work like the “PhotoPlog” but is an album/gallery component on the forum now.
See more
See less

Moldit-D and Transpiration

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Moldit-D and Transpiration

    Hi,
    I'm a newbie to the forum and midway through installation of a Valoriani 110 cm modular. I didn't get it from CA so don't have access to their forum...I have not been able to find ref-mix locally and shipping costs being what they are, I've been looking for an equivalent to add an inch to the dome for greater thermal mass. I plan to do some extended cooking...I found Moldit-D locally and the specs for elemental content are very close to ref-mix. Does anyone have experience with this material? OK to cover the dome with it?

    A different question on vents for the loose fill chamber...I plan to use perlite and cover the upper chamber with flat stone/mortar covering. The instructions that came with the oven state (in large letters) that openings must be left for transpiration. Design layout and installation photos on the CA site show no provision for this so I e-mailed Italy and the response was that the openings are definitely required-presumably to vent water vapor. I plan to use a minimum of small 1/4" holes (maybe 5-8 of them) for this purpose. Is there a discussion on this anywhere? What do most FB builders do?
    Thanks!

  • #2
    Re: Moldit-D and Transpiration

    There has been discussions regarding the venting of enclosures. Try the search function at the top of the page. If that is fruitless, read through the entire forum on finishing/enlcosures. You can pretty quickly rule out the threads that don't apply to your situation. Sounds like what you have planned should be pretty functional though.
    GJBingham
    -----------------------------------
    Everyone makes mistakes. The trick is to make mistakes when nobody is looking.

    -

    Comment


    • #3
      Re: Moldit-D and Transpiration

      If you are building your enclosure out of brick they make a nice aluminum brick vent, that just takes the place of one brick, and it's not bad looking either.





      Sorry I don't have better pictures. If you are using wonderboard over metal framing, you can use an ordinary soffit vent, although cutting a round hole will be somewhat harder than in wood.

      Venting the enclosure is not standard procedure. It seems to me that it's unlikely to cause a problem, as it would in a wooden attic.
      My geodesic oven project: part 1, part 2

      Comment


      • #4
        Re: Moldit-D and Transpiration

        Dmun,

        I used brick vents as well on my oven. I think the major reason is to make sure the insulation remains dry and air humidity does not have a chance to get at it. I really don't think just drilling holes, especially that small, will be adequate. The actual oven enclosure on my oven has the brick vents, while the gable roof area uses standard soffit vents.

        Jim
        "Made are tools, and born are hands"--William Blake, 1757-1827

        Comment


        • #5
          Re: Moldit-D and Transpiration

          CJ,
          What if you live in Florida and the humidity is 95 percent all summer long. Certainly, the humidiy gets in/out depending on the weather conditions. This whole idea stumps me a bit. It seems like any moderate amount of venting will allow the internal and external humidity levels to equalize.

          I assume ( I know, ass of you and me) the venting is primarily to allow moisture to escape as the oven cures. After that, the oven is subject to whatever weather conditions exists around the oven. If the enclosure is watertight, it seems like just a few and smallish vent holes would be adequate. I'm not second guessing you and David, just curious.
          Thanks
          George
          GJBingham
          -----------------------------------
          Everyone makes mistakes. The trick is to make mistakes when nobody is looking.

          -

          Comment


          • #6
            Re: Moldit-D and Transpiration

            Thanks for the responses...it would seem, after putting everything together, that a minimal number of holes will suffice. I may also consider the small round slotted aluminum disks that are sometimes used to vent construction. It seems that few vent their structures (especially dome builders) and I haven't heard any disaster reports from failure to vent, so I'm not going to agonize over it.

            As for the Moldit-D, it looks like no one has had experience with it so I'll let you know how it goes...
            Kevin

            Comment


            • #7
              Re: Moldit-D and Transpiration

              Moldit d is a 1300c refractory castable, so yes, can cover your dome with it.

              Comment

              Working...
              X