web analytics
chemney vent assembly question? - Forno Bravo Forum: The Wood-Fired Oven Community

Announcement

Collapse

New Forno Bravo Forum Feature

Forno Bravo Forum Community,

You will notice a new forum at the top of the main page called, "Ask Me Anything". This forum will be used for live one hour "Ask Me Anything" (AMA) sessions hosted by people who are knowledgeable in different areas pertaining to wood fired ovens. How it works:
- Each AMA will have a "sticky" thread where the community can post questions they would like answered during the live session. This will allow everyone to participate even if you can't be online for the live session. These questions will not be answered by the host until the live AMA; if you need an answer quickly, you should post it in the appropriate Forum area for the community to respond.
- Another thread will be posted for the live AMA. Registered users who are logged in during the live session can interact with the host by asking questions and receiving responses.
- The live thread will remain in the AMA forum to view after the session.

To kick off our AMA feature, we have invited author, chef and master bread maker and host of Pizza Quest, Peter Reinhart, to be our first host! Peter will be in the Forum on Monday, February 15th, from 7:00 - 8:00 pm EST. If you are unable to be online during the live session, you can post your questions in the sticky post. Peter will answer those questions during the live session on February 15th. You can view Peter's answers to your questions as well as what happened during the live session in the session thread.

We hope you enjoy this new feature! Please let us know if there is a topic that you'd like to have as an AMA and we'll look for a host!

Forno Bravo
See more
See less

chemney vent assembly question?

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • chemney vent assembly question?

    on my casa 90 the oven vent is not flush with the oppening I had to put the back of the vent on the dome. To make it level I had to build it up about 2.5 in up front with fire brick and refax motor. Also pushing the vent back made the opening smaller has anyone else come across this problem? Peter the mason for forno bravo was very helpful with my insulation. He assured me that it was ok to do this and that the opening would be fine. But having the dome vent not match did throw me for a loop. I think the installation guide should be little more clear on some of the steps. If anyone is thinking about buying a kit I would recomend Forn Bravo if for only the help I got from there mason Peter. I will be finishing my oven tomorow and will start my first fire next wed. So far a good experence we will see in a couple of weeks how successful I was.

  • #2
    Re: chemney vent assembly question?

    Hi Doug,

    You are right in that it is not totally intuitive. And Peter is also right that it works perfectly the way you did it. Thanks Peter!

    For background, the reason it does not line up perfectly is that the vent can be used two ways -- depending on your enclosure style. Most people want a flat decorative arch to define the opening into the oven, which is why you set the vent back to line up flush with the front of the oven vent walls. The vent also supports a type of installation where the opening is square, and stone is used to form it. That way, the vent hangs over the edge, and the stone frames everything in. I have seen installations done that way in Italy, though fewer in the U.S.

    Also, your comment that this could/should be more clear in the installation guide is well-taken. We are working on a new version of the installation guide right now, and we are working on improving that section. Thanks for the input on that.

    Go slow with the curing -- and have fun! It's going to be great.
    James
    Pizza Ovens
    Outdoor Fireplaces

    Comment


    • #3
      Re: chimney vent assembly question?

      I, too, had the same reaction when building my Casa110. I kept going back and looking at the instructions and flip-flopping the vent piece.

      I ended up using some scrap SuperIso board as filler to get the front up and the vent piece level. In the end I am happy with the result but I could have gotten by without the stress.

      J W

      Comment

      Working...
      X