web analytics
Securing Lathe to Insulation/Dome - Forno Bravo Forum: The Wood-Fired Oven Community



I'm Peter Reinhart! Ask Me Anything! Monday, February 15, 2016 7:00-8:00 pm EST

To kick off our AMA feature, we have invited author, chef and master bread maker and host of Pizza Quest, Peter Reinhart, to be our first host! Peter will be in the Forum on Monday, February 15th, from 7:00 - 8:00 pm EST. If you are unable to be online during the live session, you can post your questions in the sticky post. Peter will answer those questions during the live session on February 15th. You can view Peter's answers to your questions as well as what happened during the live session in the session thread.

Ask Me Anything New Forum Feature

You will notice a new forum at the top of the main page called, "Ask Me Anything". This forum will be used for live one hour "Ask Me Anything" (AMA) sessions hosted by people who are knowledgeable in different areas pertaining to wood fired ovens. How it works:
- Each AMA will have a "sticky" thread where the community can post questions they would like answered during the live session. This will allow everyone to participate even if you can't be online for the live session. These questions will not be answered by the host until the live AMA; if you need an answer quickly, you should post it in the appropriate Forum area for the community to respond.
- Another thread will be posted for the live AMA. Registered users who are logged in during the live session can interact with the host by asking questions and receiving responses.
- The live thread will remain in the AMA forum to view after the session.

We hope you enjoy this new feature! Please let us know if there is a topic that you'd like to have as an AMA and we'll look for a host!

Forno Bravo
See more
See less

Securing Lathe to Insulation/Dome

  • Filter
  • Time
  • Show
Clear All
new posts

  • Securing Lathe to Insulation/Dome

    Planning to do the scratch coat this weekend, any tricks to securing the lathe in place?

  • #2
    Re: Securing Lathe to Insulation/Dome

    I used 1/2" square hardware cloth and found it pretty easy to get it to stay on the dome. I cut the cloth in to smaller pieces to work with and the cut edges tended to stick to each other well, I would bend them over each other in a few places as well.

    Good luck with the scratch coat!


    • #3
      Re: Securing Lathe to Insulation/Dome

      I used 1/2" hardware cloth, also. I did not secure the mesh directly to the insulation. I added a vcrete layer over it. But cutting and fitting the wire is probably about the same.

      This link may help explain.

      Also, the wire they use to secure the mesh in the roll makes great tie wire .
      Last edited by Gulf; 01-18-2014, 08:12 AM.
      joe watson

      "A year from now, you will wish that you had started today "

      My Build
      My Picasa Web Album


      • #4
        Re: Securing Lathe to Insulation/Dome

        I use thin wire ties embedded in the refractory, but another way to secure it is to hold it in place by tieing string around it. Where the string goes across the entry arch can be cut off later when you've worked over it and things have set.
        Kindled with zeal and fired with passion.


        • #5
          Re: Securing Lathe to Insulation/Dome

          Those small plastic zip ties work well. Quick and easy. No tools required, except a small pair of needle nose pliers in some places.
          Last edited by NCMan; 01-21-2014, 05:44 PM. Reason: Add text
          My Build:

          "Believe that you can and you're halfway there".


          • #6
            Re: Securing Lathe to Insulation/Dome

            We used stucco wire mesh but the softer/thinner grade wire. Drilled holes into the counter a d heart. Ran screws and wires all around to secure. Came out perfectly round and secure
            Matthew 19:26. With God all things are possible.

            My Build: http://www.fornobravo.com/forum/f21/...les-18741.html