web analytics
Insulation question....again - Forno Bravo Forum: The Wood-Fired Oven Community



Forno Bravo Forum Thread Message

Hello, Forno Bravo Community Forum Members!

The Forno Bravo team has heard the feedback in regards to the community forum. We wanted to take the time to re-enforce our commitment to a fully engaged Forum with professional moderation.

Our top priority as a company is to fix all forum errors and issues that you are experiencing. As we are swiftly working on these problems, we want to say that we highly value the Forum Bravo Community Forum and every single community forum member.

We have set up this thread so that every member can address any concerns, issues and questions about the forum. Please feel free to ask whatever you would like in regards to the forum; let us know what issues you are experiencing so we can work on resolving them as fast as possible. However, we stress that we would like constructive engagement, so please be specific about the issue you are experiencing.

Thank you for all of your patience and continued support.

Link to topic: http://www.fornobravo.com/community/...with-new-forum
See more
See less

Insulation question....again

  • Filter
  • Time
  • Show
Clear All
new posts

  • Insulation question....again

    I'm not sure if it's too technical a question, but I can't seem to get an answer, so I'll try again.

    1) Is it a problem to put the FB Blanket on top of Vermicrete? It would make for an easier install if I filled few voids with vermicrete and then applied the FB Blanket. I have the vent complete and the exterior arch complete, but no pic. The area I'm looking to add the vermicrete is at the lower arch, instead of forming the blanket to the way that it is in the picture.

    2) If you had to choose between the 2 (as I do), would you:
    a) Cover entire structure with 1" FB Blanket and then 3"-4" of vermicrete; or
    b) Pour the side walls & rear wall (barrel vault) with 4" of vermicrete and use 3" of FB Blanket on the dome only.

    If you can imagine from the pic below: the brick is going to continue up to the where the dome starts. The area between the oven wall and the exterior wall is going to be filled one of the 2 ways above. My initial thoughts are to go with b), but am looking for other views. By the way, my budget is at $0 so buying a couple more blankets is out of the question, so I'm really looking for the best option from above

  • #2
    Re: Insulation question....again

    1) There's no problem putting the vermicrete on first, but your oven will be less efficient. You really want your best insulator to go on first, but it shouldn't harm anything if you don't do it that way.

    2) I like option B
    Oven Progress
    Bread Photos
    Oven Stand Thread


    • #3
      Re: Insulation question....again

      rlf5 - thanks! I could form the blanket first and then put some vermicrete on to keep it in place.


      • #4
        Re: Insulation question....again

        nice short barrel, can't wait to see it in action.


        • #5
          Re: Insulation question....again

          What kind of enclosure do you have planned?

          If you are going the metal stud/concrete board (house type) enclosure - I'd go for 1 inch of ceramic insulation all around with a back fill of loose vermiculite or perlite. Just make sure any holes are filled in before you pour the loose stuff!

          My oven progress -


          • #6
            Re: Insulation question....again

            Groves - thanks, me neither. I've had one small fire in it so far, and plan on another tonite, after I'm done laying some brick (exterior)

            Christo - I'm going to carry the brick up to the same level as the sidewalls of the oven. The top of the oven will have 3" of blanket, some vermicrete, then the stucco in the barrel vault shape. I'm going to carry the brick up the front on either side of the oven opening and have another hearth stone on top. Not sure if the chimney(s) are going to be stucco or brick yet. I'll take a few new pics tonite, it should at least be laid out.

            On another note, I had a "T" and "'08" blasted into the keystone in the entryway arch. It looks pretty cool. Can't wait to finish. I'm going to try to get most of the work done this weekend, including my curing fires, so I can make some pizza's next Saturday. I'm having about 40 people over for a summer get together.


            • #7
              Re: Insulation question....again

              nothing like a deadline to speed the work up, huh.

              How do you think your side walls will hold up without any buttressing? Seems like the barrel arch will be pushing the tops of those walls out with some force.


              • #8
                Re: Insulation question....again

                There will be lateral support once the brick sidewalls are brought up to the oven sidewall height. Then it will be filled with vermicrete or just vermiculite. I think it will hold up very well!


                • #9
                  Re: Insulation question....again

                  Here's a real time photo of my second fire.

                  Tomorrow, my buddy is coming to help lay up the sides,and hopefully I'll have it buttoned up by the weekend.

                  Here's another look

                  I'm definitely not having any issues with the draft.