web analytics
Stone Veneer - Forno Bravo Forum: The Wood-Fired Oven Community

Announcement

Collapse

I'm Peter Reinhart! Ask Me Anything! Monday, February 15, 2016 7:00-8:00 pm EST

To kick off our AMA feature, we have invited author, chef and master bread maker and host of Pizza Quest, Peter Reinhart, to be our first host! Peter will be in the Forum on Monday, February 15th, from 7:00 - 8:00 pm EST. If you are unable to be online during the live session, you can post your questions in the sticky post. Peter will answer those questions during the live session on February 15th. You can view Peter's answers to your questions as well as what happened during the live session in the session thread.

Ask Me Anything New Forum Feature

You will notice a new forum at the top of the main page called, "Ask Me Anything". This forum will be used for live one hour "Ask Me Anything" (AMA) sessions hosted by people who are knowledgeable in different areas pertaining to wood fired ovens. How it works:
- Each AMA will have a "sticky" thread where the community can post questions they would like answered during the live session. This will allow everyone to participate even if you can't be online for the live session. These questions will not be answered by the host until the live AMA; if you need an answer quickly, you should post it in the appropriate Forum area for the community to respond.
- Another thread will be posted for the live AMA. Registered users who are logged in during the live session can interact with the host by asking questions and receiving responses.
- The live thread will remain in the AMA forum to view after the session.

We hope you enjoy this new feature! Please let us know if there is a topic that you'd like to have as an AMA and we'll look for a host!

Forno Bravo
See more
See less

Stone Veneer

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Stone Veneer

    Has anyone used cultured or manmade stone for the outside finish of their ovens? We're in the process of building a new house and plan on using a stone veneer on the exterior. I was wondering if there were any potential problems with using a matching finish on an outdoor pizza oven. The same product is used on the exterior of fireplaces and chimneys, but thought I would check here.

    Thanks,
    Brian

  • #2
    Sounds good to me

    I don't see any problem with using a cultured stone finish product. The only place where your oven gets a little hot that might touch the finish material is at vent landing. You could either build a brick or stucco arch around the vent landing, or use the cultured stone there. Everywhere else, the finish walls are fully insulated from anything hot with lots if insulation.

    I know of at least one other builder using a cultured stone, and could put you in touch with them iif you are interested.

    James
    Pizza Ovens
    Outdoor Fireplaces

    Comment


    • #3
      cultured stone

      Brian, I am using Cultured stone over concrete backer board. Primarily to save weight, and cost - plus it is the same stone I that is on the facade of my house. I do not think you will have any problem if you use it.

      Stanley K.

      Comment


      • #4
        Great! Exactly what I wanted to hear.

        Thanks!
        Last edited by Gruneun; 04-18-2005, 06:12 AM.

        Comment


        • #5
          Re: Stone Veneer

          I am planning stone veneer finish over cement or concrete board (permabase). Do I need to waterproof the board before attaching the veneer or will the mortar take care of that? Permabase says it is impervious to water but it is not a water barrier.

          Also, any ideas on where I can find roofing that looks like authentic tile but is easy to install?

          Thanks.

          Fred

          Comment


          • #6
            Re: Stone Veneer

            Fred,
            I would use the recommended mesh tape on any of the concete board seams along with a fortified thinset mortar. Then use the same fortified mortar for installing the stone veneer. When properly trowled (spread with the smooth side first, then the notched side) it will seal the surface under the stone.

            Comment


            • #7
              Re: Stone Veneer

              Hey RT florida,

              I know this is an old post and it is exectly what I am searching for. I am planning on attching stone veneer to my pizza oven exterior walls of hardieboard and concrete blocks and wasn't sure about using a water proof barrier. The roof on my pizza oven is 2" thick concrete pored and sloped to the back. It overhangs the walls by 5 1/2" over hang on the walls ( without the stone veneer).

              I guess my questions to you are the following:

              The mortar will act as a water proof barrier?

              Do I need to apply a scratch coat first before I apply the stone venee?

              The mortar I plan on using is a product called Stone-Hold is this what I would use for a thin set or is there a better product available?
              STONE-HOLD Cement for Stonework

              I attached two pics of my oven.

              I appreciate any advice you can offer.
              Live life like you're dying....without going bankrupt

              Comment


              • #8
                Re: Stone Veneer

                The mortar is not water proof. You need to tape your joints, then coat with a product like this:

                Waterproof Membrane from Custom Building Products | The Home Depot - Model#: LQWAF1-2

                And then you can thinset the stone directly to the membrane, and if it will be a design with grout lines you should use regular Type S or N mortar for the grout.

                Comment


                • #9
                  Re: Stone Veneer

                  Tscarborough,
                  I used this stuff, Drylok to waterproof the roof of my saferoom. I know it works pretty well for that application and I know it works pretty well for waterproofing basements. I bought a five gallon can to paint my stand before I complete the french drain. I have enough to do my sides, back and then some. I am going to apply some thin face brick to the front of my stand. They will be cut on the wet saw to 3/4" thick from old brick that I have. I intend to make a decorative arch around the wood storage and grout/tuckpoint the arch and the few course brick that it will take to complete. I've noticed that even with a 36" overhang of the roof over the front of my oven that these "dog day monsoons" still allow a lot of splash (depending on the wind) up about a foot high on the front of my stand. My question is do you think that the thinset would stick to the Drylok?
                  joe watson

                  "A year from now, you will wish that you had started today "

                  My Build
                  My Picasa Web Album

                  Comment


                  • #10
                    Re: Stone Veneer

                    I am familiar with the product, but do not know if it is able to be used under thin brick. I would contact them to make sure.

                    Comment


                    • #11
                      Re: Stone Veneer

                      Thanks for the reply Tscarborough. You recommendation is exactly what I was looking for. I went to H-D today and bought some RedGard (they certainly don't give that stuff away $ 89 /gal!!!). As for the thinset I plan on using Megalite which even recommends to use their product with RedGard.
                      Awesome advice!!

                      This is starting to make sense to me now.

                      1) tape and seal all joints in cement board using Megalite,

                      2) apply two coats of RedGard

                      3) use Megalite thin set to bond Eldorado Stone (veneer) to RedGard.

                      4) use S or N type grout to fill in the joints between the veneer fieldstone.

                      One last question when bonding the stone veneer to the wall do I use a notched trowel and set them like I would if I were doing ceramic tile or do I butter the back of the stone and press it in place?
                      Live life like you're dying....without going bankrupt

                      Comment


                      • #12
                        Re: Stone Veneer

                        Full coat back buttering is the best way.

                        Comment

                        Working...
                        X