web analytics
Can you direct me to Styrofoam forming Dir.? - Forno Bravo Forum: The Wood-Fired Oven Community

Announcement

Collapse

I'm Peter Reinhart! Ask Me Anything! Monday, February 15, 2016 7:00-8:00 pm EST

To kick off our AMA feature, we have invited author, chef and master bread maker and host of Pizza Quest, Peter Reinhart, to be our first host! Peter will be in the Forum on Monday, February 15th, from 7:00 - 8:00 pm EST. If you are unable to be online during the live session, you can post your questions in the sticky post. Peter will answer those questions during the live session on February 15th. You can view Peter's answers to your questions as well as what happened during the live session in the session thread.

Ask Me Anything New Forum Feature

You will notice a new forum at the top of the main page called, "Ask Me Anything". This forum will be used for live one hour "Ask Me Anything" (AMA) sessions hosted by people who are knowledgeable in different areas pertaining to wood fired ovens. How it works:
- Each AMA will have a "sticky" thread where the community can post questions they would like answered during the live session. This will allow everyone to participate even if you can't be online for the live session. These questions will not be answered by the host until the live AMA; if you need an answer quickly, you should post it in the appropriate Forum area for the community to respond.
- Another thread will be posted for the live AMA. Registered users who are logged in during the live session can interact with the host by asking questions and receiving responses.
- The live thread will remain in the AMA forum to view after the session.

We hope you enjoy this new feature! Please let us know if there is a topic that you'd like to have as an AMA and we'll look for a host!

Forno Bravo
See more
See less

Can you direct me to Styrofoam forming Dir.?

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Can you direct me to Styrofoam forming Dir.?

    I have been advised to form my dome as a parabolic? hyperbolic? 3D shape.
    I plan to use styrofoam or solid insulation sheets and interlock them as several have done; placing the 1/2 firebricks as concentric reducing circumference courses.

    I will try to pack construction sand between the vanes although others have had satisfactory results omitting this step, but to quote (or misquote?) a famous bulider, overdo it or don't do it

    My question is two-fold:

    1- I have seen images of the vanes but not on how the template was made to scribe that profile. Can you specify the URL where that procedure is started? ___

    2- If you know of no relevant photo images on-line, can you describe how I should draw the correct parabolic? curve for a 42 inch diameter oven? ___

    Thanks,

    Marcel
    marceld@efn.org
    "Everything should be made as simple as possible, ...
    but no simpler!" (Albert Einstein)

  • #2
    marcel,
    all i did was lay out my bricks on a piece of board (in hindsight i would have done this straight onto a piece of styrofoam), with the 42" edges marked (representing the inside edge of my walls/diameter of the floor), and an 18" mark in the middle, telling me roughly how high i wanted the center of the dome.
    then i just layed bricks out, starting with the first vertical course, until i had figured out a number of bricks that would fit in the desired dimensions. then i played with this shape until i got something a liked ( i was shooting for a slightly flatter top), which ended up being 17.5" high, with the parabolic shape you can see in this picture.



    then, i just traced the inside line of the bricks. i measured in 21" from the edge, put a square on it, and only cut out half of the template, so that the dome would be perfectly symmetrical all the way around. i then used this half-template to remake the first two full templates. to put these first 2 vanes together, i just slotted one halfway down the center, and the other halfway up, and then slid them onto each other.

    .

    filling the cores with sand seems like it would be helpful, as there were places toward the middle where gravity started showing its presence, but the vanes hadn't closed in enough to completely hold them. but i bet they'll be hard to tear apart. the styrofoam is easy to break apart when you can bend it, but i'm not so sure with it sandwiched in tightly. i found it easy to just keep making the same template (cutting a bit off of the inside edge each time to allow it to fit between the previous vanes) over and over until it seemed pretty solid. i did 16 vanes, but where's the limit?
    -Paul
    overdo it or don't do it at all!

    My 2005 pompeii build

    Comment

    Working...
    X